Home › Drivetrain › K320 (MULTIDRIVE / CVT) › VALVE BODY ASSEMBLY › 2020.03–2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422072 VALVE BODY ASSEMBLY A

K320 MULTIDRIVE / CVT  VALVE BODY ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Shift shock may increase after replacing the transmission valve body assembly. In this case, shift shock will reduce as the vehicle is driven.


PROCEDURE

Hide 35410J 1.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

NOTICE:

Before installing the transmission valve body assembly, check that the shift lever is in D.


a.

Coat 3 new transaxle case gaskets with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.


b.

Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.


c.

Align the slit portion of the manual valve and the manual valve link lever sub-assembly as shown in the illustration, and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 2 bolts.

C434357C01
1.99,0.99 2.135,0.99 false 2,0.51 2.25,0.51 false 1.823,0.896 2.094,1.135 0.271,0.24 10 false *1 1.833,0.406 2.104,0.604 0.271,0.198 10 false *2
*1 Manual Valve *2 Manual Valve Link Lever Sub-assembly


Bolt Length:

40 mm (1.57 in.)


NOTICE:
C467180

Securely align the wire harness with the cutout of the transaxle case sub-assembly.



d.
C434358N01
0.75,1.354 0.906,1.552 0.156,0.198 10 true A 0.719,1.677 0.875,1.875 0.156,0.198 10 true B 0.646,2.49 0.802,2.688 0.156,0.198 10 true B 1.406,3.24 1.594,3.406 0.188,0.167 10 true B 1.896,2.49 2.052,2.688 0.156,0.198 10 true B 2.083,0.281 2.24,0.479 0.156,0.198 10 true B 2.813,1.625 2.969,1.823 0.156,0.198 10 true A 2.823,1.885 2.979,2.083 0.156,0.198 10 true A 2.813,2.219 2.969,2.417 0.156,0.198 10 true A

Temporarily install the 9 bolts.

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 55 mm (2.17 in.)



e.
C395524

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the temperature sensor.


f.
C399134

Connect the temperature sensor to the transmission valve body assembly.

NOTICE:

To prevent it from being pinched between the transmission valve body assembly and the transaxle side cover sub-assembly, do not let the transmission wire ride up over the area shown in the illustration.

C399135C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area. - -




g.

Temporarily install the temperature sensor clamp to the transmission valve body assembly with the bolt.

Bolt Length:

55 mm (2.17 in.)



h.
C434359

Fully tighten the 12 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


i.

Connect the 6 solenoid valve connectors.


j.

Engage the clamp to connect the transmission wire to the solenoid lock plate.


Hide 35015Y 2.INSTALL TRANSAXLE SIDE COVER SUB-ASSEMBLY

Hide 3.CHECK CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM

NOTICE:

If continuously variable transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION