Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › CAMSHAFT TIMING CONTROL MOTOR
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0422218 CAMSHAFT TIMING CONTROL MOTOR A

M15A-FXE ENGINE CONTROL  CAMSHAFT TIMING CONTROL MOTOR  INSTALLATION  


PROCEDURE

Hide 13090E 1.INSTALL CAM TIMING CONTROL MOTOR O-RING

a.
A463097C01
2.281,1.208 1.906,0.906 true 1.438,1.573 1.063,1.271 true 1.479,1.521 1.729,1.74 0.25,0.219 10 true *a 2.333,1.167 2.583,1.385 0.25,0.219 10 true *b
*a Protrusion
*b Cutout


Install a new cam timing control motor O-ring to the No. 2 timing chain cover assembly with the protrusion of the cam timing control motor O-ring oriented as shown in the illustration.


Hide 13090E 2.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

HINT:

Perform "Inspection After Repair" after removing and installing, or replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A463098C01
1.708,1.26 0.99,1.677 0.99,1.677 1.479,1.031 true 0.75,1.719 1.063,1.917 0.313,0.198 10 true *a
*a Cutout


Turn the cutout of the camshaft timing gear assembly eccentric shaft counterclockwise by hand, and set it to the maximum retard angle position.

HINT:
·

If a camshaft lobe is opening a valve, the eccentric shaft will be difficult to turn.

·

When the cutout of the camshaft timing gear assembly eccentric shaft cannot be turned any farther, it is set to the maximum retard angle.




b.
A458748C02
0.906,1.229 0.5,0.417 0.5,0.417 1.083,1.135 true 1.375,0.875 1.281,1.885 1.281,1.885 0.448,1.427 true 2.021,0.844 1.906,1.854 1.906,1.854 3.021,1.573 true 2.75,1.26 2.99,0.521 2.99,0.521 2.583,1.042 true 0.313,0.271 0.625,0.469 0.313,0.198 10 false *a 1.281,1.896 1.594,2.094 0.313,0.198 10 false *c 1.708,1.896 2.021,2.094 0.313,0.198 10 true *d 3.031,0.396 3.344,0.594 0.313,0.198 10 true *b
*a Joint
*b Cutout
*c Pin Hole
*d Knock Pin


Install the cam timing control motor with EDU assembly to the No. 2 timing chain cover assembly.

NOTICE:
·

When installing, align the joints of the cam timing control motor with EDU assembly with the cutouts of the camshaft timing gear assembly eccentric shaft.

·

Align the pin holes of the cam timing control motor with EDU assembly with the knock pins of the No. 2 timing chain cover assembly when installing the cam timing control motor with EDU assembly.

·

Make sure the contact surface of the cam timing control motor with EDU assembly (the surface that contacts the No. 2 timing chain cover assembly) is free of foreign matter.

·

When installing the cam timing control motor with EDU assembly, do not use excessive force.

·

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.

·

Do not disassemble the cam timing control motor with EDU assembly. If disassembled, replace it.




c.

Install the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the cam timing control motor with EDU assembly connector.


Hide 3.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 5. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 6.INSPECT FOR ENGINE OIL LEAK

Hide 7.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after removing and installing, or replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION