Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424238 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Communication stop for "Hybrid Vehicle Control2" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Hybrid vehicle control ECU branch line or connector

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU ground circuit

·

Hybrid vehicle control ECU



WIRING DIAGRAM

C434135E01
1.75,0.438 2,0.604 0.25,0.167 10 false 4 1.719,0.99 2.052,1.156 0.333,0.167 10 false 15 1.719,2.042 2.052,2.208 0.333,0.167 10 false 10 1.729,2.583 2.063,2.75 0.333,0.167 10 false 21 0.219,1.427 0.635,1.594 0.417,0.167 10 false H116 0.219,1.583 2.656,1.854 2.438,0.271 10 false No. 5 Global CAN Junction Connector 0.615,3.073 1.031,3.24 0.417,0.167 10 false H116 0.615,3.25 1.469,3.917 0.854,0.667 10 false No. 5 Global CAN Junction Connector 5.646,0.375 5.896,0.542 0.25,0.167 10 false 9 5.552,0.531 5.823,0.74 0.271,0.208 10 false H44 5.604,0.896 5.854,1.063 0.25,0.167 10 false 22 5.906,0.542 6.406,0.708 0.5,0.167 10 false CA1H 5.917,1.083 6.417,1.25 0.5,0.167 10 false CA1L 5.917,2.156 6.417,2.323 0.5,0.167 10 false CA3P 5.917,2.688 6.417,2.854 0.5,0.167 10 false CA3N 5.604,1.969 5.854,2.135 0.25,0.167 10 false 24 5.594,2.521 5.844,2.688 0.25,0.167 10 false 11 5.625,3.594 5.875,3.76 0.25,0.167 10 false 7 5.552,3.76 5.969,3.927 0.417,0.167 10 false H44 5.552,4.292 5.969,4.458 0.417,0.167 10 false H44 5.635,4.125 5.885,4.292 0.25,0.167 10 false 8 5.552,4.833 5.969,5 0.417,0.167 10 false H44 5.594,4.667 5.844,4.833 0.25,0.167 10 false 13 5.604,5.198 5.854,5.365 0.25,0.167 10 false 26 5.552,5.354 5.833,5.552 0.281,0.198 10 false H44 5.552,5.896 5.969,6.063 0.417,0.167 10 false A68 5.604,5.74 5.854,5.906 0.25,0.167 10 false 33 5.594,6.323 5.854,6.49 0.26,0.167 10 false 15 5.552,6.5 5.885,6.667 0.333,0.167 10 false H44 5.594,6.885 5.844,7.052 0.25,0.167 10 false 10 5.552,7.042 5.865,7.25 0.313,0.208 10 false A68 5.635,7.406 5.885,7.573 0.25,0.167 10 false 1 5.552,7.573 5.885,7.74 0.333,0.167 10 false H44 5.885,3.219 6.385,3.385 0.5,0.167 10 false MREL 5.885,3.76 6.385,3.927 0.5,0.167 10 false +B1 5.896,4.292 6.396,4.458 0.5,0.167 10 false +B2 5.896,4.833 6.396,5 0.5,0.167 10 false BATT 5.896,5.906 6.396,6.073 0.5,0.167 10 false IGR 5.906,6.5 6.406,6.667 0.5,0.167 10 false E1 5.896,7.052 6.396,7.219 0.5,0.167 10 false E01 5.896,7.594 6.396,7.76 0.5,0.167 10 false E12 5.323,7.99 7.156,8.271 1.833,0.281 10 false Hybrid Vehicle Control ECU 3.823,5.521 4.99,5.688 1.167,0.167 10 false ECU-IGP NO. 1 3.906,4.99 5.073,5.156 1.167,0.167 10 false ECU-B NO. 2 4.021,3.917 4.771,4.083 0.75,0.167 10 false PM IGCT 1.813,3.74 3.302,3.969 1.49,0.229 10 false from IGCT-MAIN Relay 1.865,4.823 3.375,5.052 1.51,0.229 10 false from Auxiliary Battery 2.26,5.344 3.823,5.594 1.563,0.25 10 false from IGP Relay 5.552,1.073 5.823,1.281 0.271,0.208 10 false H44 5.552,2.146 5.823,2.354 0.271,0.208 10 false H44 5.552,2.688 5.823,2.896 0.271,0.208 10 false H44 1.948,3.208 3.333,3.427 1.385,0.219 10 false to IGCT-MAIN Relay 5.604,3.052 5.854,3.219 0.25,0.167 10 false 47 5.552,3.229 5.823,3.438 0.271,0.208 10 false H44 5.896,5.365 6.396,5.531 0.5,0.167 10 false IGP 1.854,5.885 3.417,6.135 1.563,0.25 10 false from IGR-NO. 1 Relay 3.813,6.042 4.979,6.208 1.167,0.167 10 false ECU-IGR NO. 1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HYBRID VEHICLE CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-9 (CA1H) - H44-22 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H44-24 (CA3P) - H44-11 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HYBRID VEHICLE CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU POWER SOURCE CIRCUIT)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H44-13 (BATT) - Body ground Ignition switch off 11 to 14 V
H44-26 (IGP) - Body ground Ignition switch ON 11 to 14 V
H44-33 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

3.CHECK ECU POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK ECU POWER SOURCE CIRCUIT

Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)