Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

ECM main line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

E433990E06
4.781,1.104 5.417,1.271 0.635,0.167 10 false EFI NO. 1 5.688,0.156 6.26,0.5 0.573,0.344 10 false 8 5.875,0.969 6.448,1.313 0.573,0.344 10 false BATT 5.677,1.229 6.25,1.573 0.573,0.344 10 false 9 5.875,1.375 6.448,1.719 0.573,0.344 10 false +B 5.625,1.667 6.198,2.01 0.573,0.344 10 false 35 5.875,1.781 6.448,2.125 0.573,0.344 10 false +B2 5.625,2.052 6.198,2.396 0.573,0.344 10 false 15 5.615,2.427 6.188,2.771 0.573,0.344 10 false 45 5.875,2.573 6.448,2.917 0.573,0.344 10 false EC 2.5,1.333 4.594,1.75 2.094,0.417 10 false from EFI-MAIN NO. 1 Relay 6.094,4.344 6.76,4.625 0.667,0.281 10 false ECM 5.885,2.156 6.458,2.5 0.573,0.344 10 false MREL 5.865,2.99 6.438,3.333 0.573,0.344 10 false E1D1 5.896,3.417 6.469,3.76 0.573,0.344 10 false E1 5.896,3.896 6.469,4.24 0.573,0.344 10 false E01 2.865,0.917 4.552,1.167 1.688,0.25 10 false from Auxiliary Battery 5.604,3.75 6.177,4.094 0.573,0.344 10 false 36 5.615,3.313 6.188,3.656 0.573,0.344 10 false 10 5.615,2.865 6.188,3.208 0.573,0.344 10 false 54 5.677,0.854 6.25,1.198 0.573,0.344 10 false 1 5.615,0.521 6.188,0.865 0.573,0.344 10 false 18 0.406,1.229 2.073,1.76 1.667,0.531 10 false No. 6 Global CAN Junction Connector 0.417,1.052 0.906,1.365 0.49,0.313 10 false H117 1.667,0.51 2.156,0.823 0.49,0.313 10 false 12 1.667,0.135 2.156,0.448 0.49,0.313 10 false 1 6.146,0.208 6.719,0.552 0.573,0.344 10 false CANH 6.156,0.594 6.729,0.938 0.573,0.344 10 false CANL 2.479,2.115 4.302,2.344 1.823,0.229 10 false from EFI-MAIN NO. 1 Relay 6.094,4.177 6.667,4.521 0.573,0.344 10 false A54

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (CANH) - A54-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

2.CHECK ECM POWER SOURCE CIRCUIT

Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)