Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 2 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

TCM

·

ECM

·

No. 6 global CAN junction connector



WIRING DIAGRAM

C430894E01
0.323,2.563 2.26,2.99 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 0.323,2.385 0.823,2.615 0.5,0.229 10 false H40 2.542,4.74 5.177,5.042 2.635,0.302 10 false No. 6 Global CAN Junction Connector 2.542,4.573 3.042,4.802 0.5,0.229 10 false H117 6,3.906 6.5,4.135 0.5,0.229 10 false 120 Ω 4.146,1.354 4.469,1.573 0.323,0.219 10 false 4 2.802,1.365 3.125,1.583 0.323,0.219 10 false 3 1.792,1.917 2.115,2.135 0.323,0.219 10 false 25 1.781,1.385 2.104,1.604 0.323,0.219 10 false 26 4.135,3.521 4.458,3.74 0.323,0.219 10 false 1 4.104,4.052 4.427,4.271 0.323,0.219 10 false 12 5.125,1.365 5.448,1.583 0.323,0.219 10 false 15 1.302,1.385 1.802,1.615 0.5,0.229 10 false CA4H 1.333,1.917 1.833,2.146 0.5,0.229 10 false CA4L 2.76,1.906 3.083,2.125 0.323,0.219 10 false 14 4.115,1.906 4.438,2.125 0.323,0.219 10 false 15 5.313,3.521 5.813,3.75 0.5,0.229 10 false CANH 5.323,4.052 5.823,4.281 0.5,0.229 10 false CANL 5.073,4.042 5.396,4.26 0.323,0.219 10 false 18 5.115,3.521 5.438,3.74 0.323,0.219 10 false 8 5.771,4.552 6.271,4.781 0.5,0.229 10 false A54 0.615,1.75 1.115,1.979 0.5,0.229 10 false 120 Ω 5.125,1.906 5.448,2.125 0.323,0.219 10 false 16 5.365,1.49 5.865,1.719 0.5,0.229 10 false CANH 5.375,2.031 5.875,2.26 0.5,0.229 10 false CANL 5.729,2.406 6.229,2.635 0.5,0.229 10 false D71 5.698,2.583 6.385,2.896 0.688,0.313 10 false TCM 5.75,4.719 6.385,5.042 0.635,0.323 10 false ECM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C425195C23
1.448,0.104 1.958,0.313 0.51,0.208 2.479,1.792 2.104,0.896 true 0.958,1.802 2.01,0.896 true 2.313,1.833 2.927,2.031 0.615,0.198 10 false CA4L 0.781,1.844 1.396,2.042 0.615,0.198 10 false CA4H 1.594,0.146 2.052,0.344 0.458,0.198 10 false H40 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

23.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C24
1.448,0.104 1.958,0.313 0.51,0.208 2.479,1.792 2.104,0.896 true 0.958,1.802 2.01,0.896 true 2.313,1.833 2.927,2.031 0.615,0.198 10 false CA4L 0.781,1.844 1.396,2.042 0.615,0.198 10 false CA4H 1.594,0.146 2.052,0.344 0.458,0.198 10 false H40 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

17.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C14
1.917,0.25 2.417,0.5 0.5,0.25 5.281,0.25 5.781,0.5 0.5,0.25 1.646,2.198 2.375,1.302 true 2.5,1.302 3.042,2.167 true 6.292,1.604 6.469,1.958 true 3.938,0.25 4.25,0.448 0.313,0.198 10 false *1 2.031,0.281 2.427,0.479 0.396,0.198 10 false H40 3.073,2.146 3.625,2.344 0.552,0.198 10 false CA4L 6.521,1.854 7.073,2.052 0.552,0.198 10 false BAT 1.198,2.156 1.75,2.354 0.552,0.198 10 false CA4H 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 5.448,0.271 5.844,0.469 0.396,0.198 10 false H3
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H40-25 (CA4L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

11.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C15
5.25,0.25 5.75,0.5 0.5,0.25 1.865,0.25 2.365,0.5 0.5,0.25 2.5,1.302 3.188,2.167 true 2.385,1.302 1.615,2.208 true 5.417,1.219 4.927,2.052 true 3.958,0.271 4.271,0.469 0.313,0.198 10 false *1 1.979,0.271 2.375,0.469 0.396,0.198 10 false H40 3.24,2.135 3.792,2.333 0.552,0.198 10 false CA4L 4.667,1.979 5.219,2.177 0.552,0.198 10 false CG 1.167,2.156 1.719,2.354 0.552,0.198 10 false CA4H 5.406,0.271 5.719,0.469 0.313,0.198 10 false H3 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
H40-25 (CA4L) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
H40-25(CA4L) - H3-4 (CG)



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A54-18 (CANL) - H3-4 (CG)



c.

Reconnect the ECM connector.


Result:
Result
OK
NG



OK

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
H117-14 (CANL) - H3-4 (CG)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM
H117-15 (CANL) - H3-4 (CG)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
H117-12 (CANL) - H3-4 (CG)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D71-15 (CANH) - H3-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
D71-16 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

11.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H40-25 (CA4L) - H3-16 (BAT)



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

12.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A54-18 (CANL) - H3-16 (BAT)



c.

Reconnect the ECM connector.


Result:
Result
OK
NG



OK

NG

13.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
13.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-3 (CANH) -H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
H117-14 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

14.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

14.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher TCM
H117-15 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

15.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

16.CHECK FOR SHORT TO +B IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
15.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
H117-12 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

16.CHECK FOR SHORT TO +B IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D71-15 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
D71-16 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

18.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
18.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (CANH) - A54-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the ECM connector.


Result:
Result
OK
NG



OK

NG

19.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
19.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-3 (CANH) - H117-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

20.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

20.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-4 (CANH) - H117-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

21.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

22.CHECK FOR SHORT IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
21.CHECK FOR SHORT IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-1 (CANH) - H117-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

22.CHECK FOR SHORT IN CAN BUS LINE (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D71-15 (CANH) - D71-16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TCM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

23.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

24.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
24.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-8 (CANH) - A54-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the ECM connector.


Result:
Result
OK
NG



OK

NG

25.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
25.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-3 (CANH) - H117-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

26.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION TERMINAL - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

26.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION TERMINAL - ECM)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H117-1 (CANH) - H117-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



c.

Reconnect the No. 6 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)