Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2020.03–2020.07
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E422634E06
2.26,3.021 3.635,3.219 1.375,0.198 10 false *: Shielded 0.458,2.917 1.656,3.302 1.198,0.385 10 false Radio and Display Receiver Assembly 1.021,2.417 1.479,2.635 0.458,0.219 10 false CSLD 1,2.052 1.5,2.271 0.5,0.219 10 false CGND 1.229,1.104 1.615,1.302 0.385,0.198 10 false V- 1.229,0.604 1.615,0.802 0.385,0.198 10 false V+ 1.125,1.604 1.51,1.802 0.385,0.198 10 false CA+ 1.49,1.51 1.875,1.708 0.385,0.198 10 false 30 3.406,2.292 3.792,2.49 0.385,0.198 10 false * 5.438,2.771 6,2.958 0.563,0.188 10 false Y2 5.521,1.615 5.906,1.813 0.385,0.198 10 false CB+ 5.521,0.604 5.906,0.802 0.385,0.198 10 false CV+ 5.521,1.115 5.906,1.313 0.385,0.198 10 false CV- 5.521,2.083 6.031,2.292 0.51,0.208 10 false CGND 5.333,1.5 5.719,1.698 0.385,0.198 10 false 6 5.313,0.5 5.698,0.698 0.385,0.198 10 false 3 5.323,1 5.708,1.198 0.385,0.198 10 false 2 5.333,1.948 5.719,2.146 0.385,0.198 10 false 5 0.458,2.75 0.844,2.948 0.385,0.198 10 false H80 1.5,0.5 1.885,0.698 0.385,0.198 10 false 28 1.5,1 1.885,1.198 0.385,0.198 10 false 29 1.5,1.958 1.885,2.156 0.385,0.198 10 false 27 1.5,2.302 1.885,2.5 0.385,0.198 10 false 26 5.438,2.958 6.896,3.396 1.458,0.438 10 false Rear Television Camera Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the Y2 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-30 (CA+) - Y2-6 (CB+) Always Below 1 Ω
H80-28 (V+) - Y2-3 (CV+) Always Below 1 Ω
H80-29 (V-) - Y2-2 (CV-) Always Below 1 Ω
H80-27 (CGND) - Y2-5 (CGND) Always Below 1 Ω
H80-26 (CSLD) - Body ground Always Below 1 Ω
H80-30 (CA+) or Y2-6 (CB+) - Body ground Always 10 kΩ or higher
H80-28 (V+) or Y2-3 (CV+) - Body ground Always 10 kΩ or higher
H80-29 (V-) or Y2-2 (CV-) - Body ground Always 10 kΩ or higher
H80-27 (CGND) or Y2-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the H80 radio and display receiver assembly connector.


b.
E366062C69
1.427,0.198 1.917,0.479 0.49,0.281 0.542,1.073 1.042,1.344 true 0.771,1.76 1.167,1.375 true 1.333,1.875 1.438,1.375 true 1.552,0.25 1.865,0.448 0.313,0.198 10 false H80 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.344,0.875 0.802,1.073 0.458,0.198 10 false CA+ 0.635,1.771 0.948,1.969 0.313,0.198 10 false V- 1.156,1.896 1.771,2.094 0.615,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-29 (V-) - Body ground Always Below 1 Ω
H80-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H80-30 (CA+) - H80-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the Y2 rear television camera assembly connector.


b.
E366062C70
1.5,0.25 1.917,0.5 0.417,0.25 1.177,1.354 0.583,0.917 true 1.26,1.375 0.906,1.896 true 1.583,0.281 2.083,0.521 0.5,0.24 10 false H80 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,0.813 0.729,1.031 0.354,0.219 10 false V- 0.698,1.813 1.052,2.031 0.354,0.219 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C37
0.76,1.99 1.115,1.583 true 0.75,4.063 1.135,3.604 true 1.604,4.052 1.271,3.542 true 1.573,1.958 1.229,1.479 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.052 1.906,4.313 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal H80-28 (V+) - H80-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY