Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424587 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of HV battery
1.

Prediagnostic battery charge

2.

Battery diagnosis

3.

Battery status info update


HV battery status information cannot be updated (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A457840

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A457841C02
0.99,2.521 0.458,2.042 0.458,2.042 0.885,1.125 true 0.229,1.958 0.542,2.115 0.313,0.156 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery assembly, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



Hide 2. READ VALUE USING TECHSTREAM

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Temperature 1 to 6.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67

d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide 7.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A464113C02
2.063,1.417 2.313,1.615 0.25,0.198 10 true *a 1.896,0.5 2.146,0.698 0.25,0.198 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.



b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 73350C 9.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 12.REMOVE REAR UNDER COVER

a.
A464098

Disengage the 3 clips.


b.

Disengage the 2 guides to remove the rear under cover from the rear seat cushion leg sub-assembly.


Hide 71033 13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A464099

Remove the 6 bolts and rear seat cushion leg sub-assembly.


Hide G9230 14.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N1 15.REMOVE HV BATTERY UPPER COVER PANEL

CAUTION:

Wear insulated gloves.


a.
A464102C01
2.792,2.031 3.094,2.031 false 2.76,3.01 3.063,3.01 false 2.635,2.854 2.802,2.625 2.802,2.625 2.958,2.625 true 2.208,2.698 2.406,2.698 2.406,2.698 2.573,2.49 false 3.115,1.927 3.427,2.125 0.313,0.198 10 false *1 3.083,2.906 3.396,3.104 0.313,0.198 10 false *2 2.021,2.323 2.333,2.521 0.313,0.198 10 false *b 2.042,2.604 2.354,2.802 0.313,0.198 10 false *a 3,2.51 3.313,2.708 0.313,0.198 10 false *c
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 5 nuts and HV battery upper cover panel from the HV battery.


Hide 821H1 16.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.


a.
A464103C02
2.354,0.583 2.656,0.354 true 2.698,0.24 2.948,0.458 0.25,0.219 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.


b.

Disconnect the shield ground from the HV battery.


Hide 82161 17.DISCONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.
A464105

Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


Hide G929A 18.REMOVE NO.1 HV BATTERY HOSE

a.
A464107

Disconnect the No. 1 HV battery hose from the vehicle.


b.

Disengage the 2 claws to remove the No. 1 HV battery hose from the HV battery.


Hide 82161 19.DISCONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.
A464106

Disengage the clamp.


b.

Disconnect the HV battery connector.


Hide G9510 20.REMOVE HV BATTERY

CAUTION:

Wear insulated gloves.


a.
A464108

Remove the 4 bolts and HV battery from the vehicle.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




Hide 21.PERFORM RECOVERY INSPECTION

a.

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION