G9510
1.INSTALL HV BATTERY
Wear insulated gloves.
Align the centers of the bolt holes on the HV battery bracket with the centers of the vehicle-side bolt holes as shown in the illustration.
| *a | HV battery bracket | *b | Vehicle |
|
Front of Vehicle | - | - |
Install the HV battery to the vehicle with the 3 bolts (A) and bolt (B).
| *a | Bolt (A)
(Bolt Length: 25 mm (0.984 in.)) |
*b | Bolt (B)
(Bolt Length: 24 mm (0.945 in.)) |
|
Front of Vehicle | - | - |
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
Use cardboard or another similar material to protect the HV battery and vehicle body from damage.
Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.
When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.
While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.
As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.
If the HV battery has been struck or dropped, replace it.
82161
2.CONNECT FLOOR WIRE
Wear insulated gloves.
Connect the HV battery connector.
Engage the clamp.
G929A
3.INSTALL NO.1 HV BATTERY HOSE
Engage the 2 claws to install the No. 1 HV battery hose to the HV battery.
Connect the No. 1 HV battery hose to the vehicle.
82161
4.CONNECT FLOOR WIRE
Wear insulated gloves.
Connect the HV battery junction block assembly connector.
Connect the electric vehicle battery plug assembly connector.
Engage the clamp.
821H1
5.CONNECT FLOOR UNDER WIRE
Wear insulated gloves.
Connect the shield ground to the HV battery.
Connect the 2 HV battery junction block assembly connectors.
Make sure that the connectors are connected securely.
G92N1
6.INSTALL HV BATTERY UPPER COVER PANEL
Wear insulated gloves.
| *1 | Battery Cover Lock Striker |
| *a | Button |
| *b | Push |
Install the HV battery upper cover panel to the HV battery with the 5 nuts.
Install the battery cover lock striker, then push the button to lock it.
G9230
7.INSTALL BATTERY COOLING BLOWER ASSEMBLY
71033
8.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
Temporarily install the rear seat cushion leg sub-assembly with the 6 bolts.
Fully tighten the 6 bolts in the order shown in the illustration.
76971G
9.INSTALL REAR UNDER COVER
Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.
Engage the 3 clips.
72693
10.INSTALL REAR SEAT CUSHION LOCK HOOK
11.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
73350C
12.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
G3834
13.INSTALL SERVICE PLUG GRIP
14. PERFORM UTILITY
Perform "Battery Status Info Update" after replacing the malfunctioning HV battery.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY
Perform "Prediagnostic Battery Charge" after replacing the malfunctioning HV battery.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY
Perform "Battery Diagnosis" after replacing the malfunctioning HV battery.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY