Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424637 REAR CRANKSHAFT OIL SEAL A

M15A-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




c.

Using SST and a hammer, tap in the rear engine oil seal.

A460240C01
1.677,1.229 1.125,0.802 1.125,0.802 2.135,0.615 true 0.823,0.74 1.281,0.938 0.458,0.198 10 false SST 5.063,0.229 5.521,0.427 0.458,0.198 10 false *a
*a -0.9 to 1.1 mm - -


SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A464822

Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A464394N01
1.042,1.073 0.552,1.073 0.552,1.073 0.813,0.646 false 0.229,1 0.688,1.198 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.

Clean the bolt holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A464825N01
1.635,0.208 1.792,0.406 0.156,0.198 10 true 1 0.896,1 1.052,1.198 0.156,0.198 10 true 3 2.156,0.406 2.313,0.604 0.156,0.198 10 true 7 1.083,0.438 1.24,0.635 0.156,0.198 10 true 5 1.646,1.729 1.802,1.927 0.156,0.198 10 true 2 2.344,0.979 2.5,1.177 0.156,0.198 10 true 4 2.188,1.458 2.333,1.656 0.146,0.198 10 true 6 1.135,1.563 1.292,1.76 0.156,0.198 10 true 8

Install the flywheel sub-assembly with the 8 new bolts. Uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31270 4.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A464394N01
1.042,1.073 0.552,1.073 0.552,1.073 0.813,0.646 false 0.229,1 0.688,1.198 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A464826N01
0.958,0.031 1.115,0.229 0.156,0.198 10 true 1 2.438,1.896 2.594,2.094 0.156,0.198 10 true 2 2.344,0.021 2.5,0.219 0.156,0.198 10 true 3 1.063,1.958 1.219,2.156 0.156,0.198 10 true 4 2.854,0.875 3.01,1.073 0.156,0.198 10 true 5 0.563,1.135 0.719,1.333 0.156,0.198 10 true 6

Install the transmission input damper assembly to the flywheel sub-assembly with the 6 bolts. Uniformly tighten the 6 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that there are no oil on the transmission input damper assembly and flywheel sub-assembly.

·

Make sure to install the transmission input damper assembly in the correct direction.

·

Do not allow grease to contact the splines of the transmission input damper assembly and the input shaft.




Hide 30900 5.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY