Home › Drivetrain › CLUTCH › CLUTCH UNIT › 2020.03–2020.07
RM36W0E _52 Drivetrain _089426 CLUTCH _0424693 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 30300 2.REMOVE MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge)

Hide 30300 3.REMOVE MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge)

Hide 31483 4.REMOVE BLEEDER CLUTCH RELEASE TUBE

a.
C431522

Using a 10 mm union nut wrench, separate the bleeder clutch release tube from the clutch release bleeder sub-assembly.


b.
C431523

Remove the bolt and bleeder clutch release tube from the manual transaxle assembly.


c.
C431524

Remove the clamp from the bleeder clutch release tube.


Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C431525

Using a 10 mm union nut wrench, separate the clutch release bleeder sub-assembly from the clutch release cylinder to bleeder tube.


b.
C431526

Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.


Hide 31400 6.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C431527

Remove the clutch tube boot from the manual transaxle assembly.


b.
C431528

Remove the 3 bolts and clutch release cylinder with bearing assembly together with clutch release cylinder to bleeder tube from the manual transaxle assembly.


Hide 31483 7.REMOVE CLUTCH RELEASE CYLINDER TO BLEEDER TUBE

a.

Mount the clutch release cylinder with bearing assembly in a soft jaw vise.


b.
C401472

Using a 10 mm union nut wrench, remove the clutch release cylinder to bleeder tube from the clutch release cylinder with bearing assembly.


Hide 31210 8.REMOVE CLUTCH COVER ASSEMBLY

a.
C401473C01
1.073,0.708 0.5,0.99 0.5,0.99 1.115,0.74 true 0.281,0.958 0.583,1.135 0.302,0.177 10 false *a
*a Matchmark


Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.


b.

Loosen each bolt 180° at a time until the spring tension is released.


c.

Remove the 6 bolts and pull off the clutch cover assembly.

NOTICE:

Do not drop the clutch disc assembly.



Hide 31250 9.REMOVE CLUTCH DISC ASSEMBLY

NOTICE:

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.