Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424706 MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

EC6E MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE FRONT WHEELS

Hide 51451A 5.REMOVE ENGINE UNDER COVER CENTER

Hide 51442C 6.REMOVE ENGINE UNDER COVER LH

Hide 51441C 7.REMOVE ENGINE UNDER COVER RH

Hide 53876A 8.SEPARATE FRONT FENDER LINER LH

Hide 53875A 9.SEPARATE FRONT FENDER LINER RH

Hide 51447D 10.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 11.DRAIN MANUAL TRANSAXLE OIL

Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 13.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55735A 14.INSTALL WATER GUARD PLATE LH

Hide 55701J 15.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 16.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 17.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 19.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 20.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 17410 21.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 24.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 25.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 26.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 28100 27.REMOVE STARTER ASSEMBLY

Hide 30.INSTALL ENGINE SUPPORT BRIDGE

a.
C425928C02
0.729,0.542 1.719,1.083 true 0.906,3.208 1.625,3.635 true 0.906,2.76 1.729,3.51 true 0.729,2.677 0.885,2.833 0.156,0.156 10 true *c 0.51,0.417 0.698,0.625 0.188,0.208 10 true *a 0.719,3.094 0.906,3.26 0.188,0.167 10 true *b
*a Existing Hole
*b Protective Tape
*c Bolt


Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.

Item Part No.
Bolt 9010-10226


b.

Install SST to the vehicle body as shown in the illustration.

C435484C01
1.375,1.333 1.594,1.042 true 5.177,1.354 4.958,1.104 true 1.469,5.281 1.854,5.115 true 1.844,6 2.135,6.229 true 4.938,4.771 5.323,5.094 true 4.385,5.927 4.719,5.813 true 1.896,5.021 2.104,5.188 0.208,0.167 10 true *a 2.125,6.156 2.333,6.344 0.208,0.188 10 true *b 1.156,1.313 1.354,1.51 0.198,0.198 10 true *c 5.198,1.292 5.396,1.49 0.198,0.198 10 true *c 4.74,4.667 4.927,4.865 0.188,0.198 10 true *a 4.167,5.823 4.375,6.01 0.208,0.188 10 true *b
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


SST
09940-10010  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




c.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


d.

Install the chain block to the sling bracket.

C435485C01
0.458,0.271 1.375,0.271 false 1.063,1.479 1.396,1.479 true 1.479,1.573 1.792,1.615 true 1.667,0.667 2,0.583 false 2.042,0.5 2.354,0.656 0.313,0.156 10 false *a 0.292,0.198 0.604,0.354 0.313,0.156 10 false *b 0.865,1.406 1.031,1.594 0.167,0.188 10 true *c 1.823,1.552 1.99,1.719 0.167,0.167 10 true *d
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



e.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with manual transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




f.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

C435486C01
1.875,0.677 2.302,0.771 true 1.792,1.115 1.469,1.406 true 2.333,1.365 1.938,1.24 true 1.792,3.156 1.396,3.031 true 1.104,3.698 0.708,3.781 true 1.042,0.708 0.719,1 true 2.083,2.844 2.417,3.198 true 1.719,3.469 1.323,3.427 true 0.479,3.698 0.677,3.865 0.198,0.167 10 true *1 2.333,1.271 2.521,1.448 0.188,0.177 10 true *2 0.5,0.958 0.708,1.115 0.208,0.156 10 true *a 2.333,0.698 2.542,0.854 0.208,0.156 10 true *b 1.24,1.406 1.448,1.552 0.208,0.146 10 true *c 2.427,3.135 2.635,3.292 0.208,0.156 10 true *a 1.74,3.406 1.948,3.552 0.208,0.146 10 true *c 1.802,3.083 2.01,3.24 0.208,0.156 10 true *b
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


NOTICE:

Connect the 1st link of the chain to the No. 1 engine hanger.



g.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.



h.
C330764C02
1.219,0.792 1.531,0.948 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) or more


Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.



i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

C435487C01
4.125,0.792 4.542,0.375 false 3.271,1.333 3.583,1.51 true 3.604,1.458 3.771,1.625 0.167,0.167 10 true *a 4.583,0.292 4.896,0.448 0.313,0.156 10 false *b 5.938,0.26 6.25,0.417 0.313,0.156 10 false *c 0.938,0.25 1.25,0.406 0.313,0.156 10 false *d 5.958,2.198 6.188,2.333 0.229,0.135 10 true *f 0.906,2.177 1.104,2.333 0.198,0.156 10 true *f 2.99,0.198 3.302,0.365 0.313,0.167 10 false *e
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


CAUTION:
·

To prevent the engine with manual transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C399990C01
1.833,1.427 2.25,1.01 false 2.281,0.896 2.594,1.052 0.313,0.156 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with manual transaxle assembly and engine support bridge to fall, possibly causing serious injury.



NOTICE:
C330751

·

Do not perform any procedures if the chain of the chain block assembly is not straight.

·

When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.




j.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

C436030C01
1.281,1.844 1.5,2 0.219,0.156 10 true *b 5.74,1.823 5.958,1.979 0.219,0.156 10 true *b 2.135,0.125 2.333,0.302 0.198,0.177 10 false *a 4.813,0.083 5.01,0.26 0.198,0.177 10 false *a 4.573,1.104 4.771,1.281 0.198,0.177 10 true *a 5.156,1.281 5.354,1.458 0.198,0.177 10 true *a 2.51,1.156 2.708,1.333 0.198,0.177 10 true *a 1.865,1.271 2.063,1.448 0.198,0.177 10 true *a
*a Wing Bolt *b Bolt


Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




k.
C399992C01
2.542,2.823 2.74,3.021 0.198,0.198 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with manual transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 51201 31.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 32.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C435436

Remove the 4 bolts and No. 2 engine moving control rod from the manual transaxle assembly.


Hide 30300 34.SUPPORT MANUAL TRANSAXLE ASSEMBLY

a.
C435438C01
1.865,0.865 1.344,0.865 true 1.156,0.76 1.333,0.938 0.177,0.177 10 true *a
*a Lashing Belt


Using a transmission jack and lashing belt or rope, support the manual transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely support the manual transaxle assembly.

·

Using a lashing belt or a rope, secure the manual transaxle assembly to the transmission jack.




Hide 12372A 35.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C435439

Disengage the clamp and separate the engine wire from the engine mounting insulator LH.


b.
C435440

Remove the 4 bolts, nut and engine mounting insulator LH from manual transmission case.


c.
C435441

Remove the 4 bolts, nut and engine mountinginsulator LH from the vehicle body.


Hide 31483 37.REMOVE BLEEDER CLUTCH RELEASE TUBE

Hide 31407B 39.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 40.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31483 41.REMOVE BLEEDER CLUTCH RELEASE TUBE