Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424700 DIFFERENTIAL OIL SEAL A

EC6E MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C432088N01
0.75,2.115 0.75,1.75 false 0.656,2.125 1,2.333 0.344,0.208 10 false SST

Using SST, remove the front drive shaft oil seal LH from the manual transaxle assembly.

SST
09308-00010  


Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C432087N01
2.698,2.281 2.698,1.865 false 2.604,2.302 3.063,2.5 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the manual transaxle assembly.

SST
09308-00010  


Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C401624C01
1.906,1.438 1.5,1.917 1.5,1.917 1.156,1.229 true 1.5,1.917 1.406,1.354 true 1.385,1.938 1.844,2.135 0.458,0.198 10 false SST 0.906,3.115 1.219,3.271 0.313,0.156 10 false *a
*a Depth


Using SST and a hammer, tap in the front drive shaft oil seal RH to the manual transaxle assembly.

SST
09630-24014  (09620-24051)
09950-60011  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the front drive shaft oil seal RH lip.


NOTICE:
·
C381409C06
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal RH.

·

Do not install the front drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal RH.




Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.
C432086C01
1.583,1.417 1.583,1.083 false 1.458,1.417 1.833,1.635 0.375,0.219 10 false SST 2.302,3.021 2.677,3.24 0.375,0.219 10 false *a
*a Depth


Using SST and a hammer, tap in the front drive shaft oil seal LH to the manual transaxle assembly.

SST
09316-60012  (09316-00011)

Standard Depth:

2.3 to 3.3 mm (0.0906 to 0.1299 in.)


NOTICE:

Do not damage the front drive shaft oil seal LH lip.


NOTICE:
·
C381409C06
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.