Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FKS) › 2020.03–2020.07
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0418626 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

a.

Install a new front drive shaft hole snap ring.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.



Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.

Coat the snap ring of the front drive inboard joint assembly with MP grease.


b.

for CVT:

i.

Coat the splines of the front drive inboard joint assembly with Toyota genuine CVT fluid FE.



c.

for Manual Transaxle:

i.

Coat the splines of the front drive inboard joint assembly with Toyota genuine manual transmission gear oil LV.



d.
C406945C01
0.406,0.271 0.719,0.469 0.313,0.198 10 false *a
*a Cross Section of Front Drive Shaft Oil Seal
V100145

MP grease
V100144

Toyota Genuine Oil Seal Side Lip Grease


Coat the lip of the front drive shaft oil seal with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.

HINT:

Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal.



e.
C439746

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



f.
C434171C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


g.
C434172C01
2.427,0.625 2.115,1.594 2.115,1.594 2.51,0.792 true 1.979,1.594 2.438,1.792 0.458,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly to the front axle assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not damage the front axle outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the deflector.




Hide 48069 3.INSTALL FRONT LOWER NO.1 SUSPENSION ARM SUB-ASSEMBLY

Hide 48810 4.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 45047 5.INSTALL TIE ROD END SUB-ASSEMBLY

Hide 89543 6.INSTALL FRONT SPEED SENSOR

Hide 43502H 7.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C434173

Using a 30 mm deep socket wrench, install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 8.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 9.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 10.INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)

Hide 11.INSTALL FRONT WHEELS

Hide 12.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51442C 13.INSTALL ENGINE UNDER COVER LH

Hide 51441C 14.INSTALL ENGINE UNDER COVER RH

Hide 51451A 15.INSTALL CENTER ENGINE UNDER COVER

Hide 17.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)