The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake removal/installation are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION (for HV Model)
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISABLE BRAKE CONTROL (for HV Model)
Wait at least 2 minutes after turning the power switch off.
When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.
Disconnect the reservoir level switch connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal cannot be further depressed.
3.REMOVE FRONT WHEEL
4.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
47313J
5.DISCONNECT FRONT FLEXIBLE HOSE
Remove the union bolt and gasket, and disconnect the front flexible hose from the front disc brake cylinder assembly.
6.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY
| *a | Turn |
| *b | Hold |
Hold the 2 front disc brake cylinder slide pins and remove the 2 bolts and front disc brake cylinder assembly.
7.REMOVE ANTI-SQUEAL SPRING
Remove the anti-squeal spring from the front disc brake pad.
8.REMOVE FRONT DISC BRAKE PAD
Remove the 2 front disc brake pads from the front disc brake cylinder mounting.
9.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT
10.REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
Remove the 4 front disc brake pad support plates from the front disc brake cylinder mounting.
Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.
11.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN
Remove the 2 front disc brake cylinder slide pins from the front disc brake cylinder mounting.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake cylinder slide bushing from the front disc brake cylinder slide pin (lower side).
Do not damage the front disc brake cylinder slide pin.
12.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT
Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.
13.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING
Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.
43512
14.REMOVE FRONT DISC
| *a | Matchmark |
Put matchmarks on the front disc and the front axle hub sub-assembly.
Remove the front disc.