The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.
When using the GTS with the vehicle ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*
*: w/ Entry and Start System
The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the Active Test according to the display on the GTS.
| Tester Display |
|---|
| Trunk Lid / Back Door Open |
The back door lock assembly with courtesy light switch unlatches when ON is selected.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Trunk Lid / Back Door Open | Back door lock motor | OFF/ON | - |
| Result | Proceed to |
|---|---|
| OK (w/ Entry Function) | A |
| OK (w/o Entry Function) | B |
| NG | C |
A
for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
OK
NG
Disconnect the Y8 back door opener switch assembly connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y8-3 (UL) - H4-19 (BDSU) | Always | Below 1 Ω |
| Y8-2 (E) - Body ground | Always | Below 1 Ω |
| Y8-3 (UL) or H4-19 (BDSU) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the Y7 back door lock assembly with courtesy light switch connector.
Disconnect the 4E power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y7-1 (ACT+) - 4E-39 | Always | Below 1 Ω |
| Y7-3 (D+) - 4E-2 | Always | Below 1 Ω |
| Y7-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Y7-1 (ACT+) or 4E-39 - Body ground | Always | 10 kΩ or higher |
| Y7-3 (D+) or 4E-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Power Distribution Box Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-19 (BCTY) - 4E-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the power distribution box assembly connectors.
| *a | Component without harness connected
(Power Distribution Box Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4F-1 - Body ground | Ignition switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-36 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Power Distribution Box Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-36 - 4E-39 | Auxiliary battery voltage applied between 4F-1 and MB-5(TR+) | 10 kΩ or higher |
| 4B-36 - 4E-39 | Auxiliary battery voltage not applied between 4F-1 and MB-5(TR+) | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4E-39 - Auxiliary battery negative (-) terminal | Auxiliary battery voltage applied between 4F-1 and MB-5 (TR+) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG