Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for Gasoline Model without Entry and Start System) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424970 IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light (combination meter assembly) when the immobiliser is set (no key is in the ignition key cylinder).


WIRING DIAGRAM

E438746E01
2.052,0.969 2.313,1.156 0.26,0.188 10 false LP 2.365,0.969 2.625,1.156 0.26,0.188 10 false 7 0.656,1.542 0.969,1.698 0.313,0.156 10 false H7 0.635,1.708 2.896,2.104 2.26,0.396 10 false Security Indicator Light (Combination Meter Assembly) 4.99,0.969 5.25,1.156 0.26,0.188 10 false 8 5.229,0.969 5.49,1.156 0.26,0.188 10 false IND 5.677,0.708 6.063,0.906 0.385,0.198 10 false +B 5.021,1.813 5.406,2.01 0.385,0.198 10 false H74 5.01,1.979 6.396,2.448 1.385,0.469 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light (combination meter assembly) ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the H7 security indicator light (combination meter assembly) connector.


b.

Disconnect the H74 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-8 (IND) - H7-7 (LP) Always Below 1 Ω
H74-8 (IND) or H7-7 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the H74 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-8 (IND) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY