Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424998 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1AAE00  Front Recognition Camera Heater Malfunction  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.

If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE00 Front Recognition Camera Heater Malfunction
Either of the following conditions is met after 10 seconds have elapsed since the ignition switch was turned to ON:
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Wire harness or connector



DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition After 10 seconds have elapsed since the ignition switch was turned to ON ○ ○ ○
Malfunction Status Short to +B detected in the forward recognition with heater hood sub-assembly circuit. ○ - -
Open to ground detected in the forward recognition with heater hood sub-assembly circuit. - ○ -
Short to ground detected in the forward recognition with heater hood sub-assembly circuit. - - ○
Detection Time 1 second or more 5 seconds or more 5 seconds or more
Number of Trips 1 trip 1 trip 1 trip

WIRING DIAGRAM

A398326E75
0.083,0.667 3.146,0.865 3.063,0.198 10 false from IGR-NO. 2 Relay 2.031,0.833 3.073,1.052 1.042,0.219 10 false ECU-IGR NO. 2 3.177,1.229 4.885,1.646 1.708,0.417 10 false Forward Recognition with Heater Hood Sub-assembly 3.583,0.708 4.042,0.906 0.458,0.198 10 false IG1 4.125,0.698 4.583,0.896 0.458,0.198 10 false HTR 3.396,0.594 3.552,0.792 0.156,0.198 10 false 1 4.5,0.583 4.656,0.781 0.156,0.198 10 false 2 5.344,0.583 5.5,0.781 0.156,0.198 10 false 1 5.531,0.688 5.99,0.885 0.458,0.198 10 false HTR 3.177,1.052 4.094,1.25 0.917,0.198 10 false V11 5.104,2.073 5.563,2.271 0.458,0.198 10 false V10 5.094,2.26 6.958,2.49 1.865,0.229 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTCs
2.CHECK FOR DTCs
a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



b.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTC C1AAE00 is not output A
DTC C1AAE00 is output B



A

B

3.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
3.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the V11 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
V11-1 (IG1) - V11-2 (HTR) Ignition switch off 25.6 to 28.4 Ω



d.

Connect the V11 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.

Disconnect the V11 forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V11-1 (IG1) - Body ground Ignition switch ON 8 to 16 V
Ignition switch off Below 1.5 V



c.

Connect the V11 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V11 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the V10 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V11-2 (HTR) - V10-1 (HTR) Always Below 1 Ω
V11-2 (HTR) or V10-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Connect the V10 forward recognition camera connector.


e.

Connect the V11 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)