Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424992 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Security Indicator Light Does not Blink  


DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light (combination meter assembly) when the immobiliser is set (ignition switch off).

WIRING DIAGRAM

B547117E04
0.927,1.771 3.198,2.219 2.271,0.448 10 false Security Indicator Light (Combination Meter Assembly) 0.927,1.604 1.281,1.885 0.354,0.281 10 false H7 0.646,2.417 2.896,2.677 2.25,0.26 10 false : CAN Communication Line 2.031,0.99 2.26,1.198 0.229,0.208 10 false LP 2.344,0.823 2.698,1.104 0.354,0.281 10 false 7 4.448,0.875 4.698,1.073 0.25,0.198 10 false 25 4.719,0.875 5.073,1.156 0.354,0.281 10 false IND 5.385,0.406 5.74,0.688 0.354,0.281 10 false +B 4.385,1.719 4.74,2 0.354,0.281 10 false H46 6.125,1.813 7.135,2.729 1.01,0.917 10 false Main Body ECU (Multiplex Network Body ECU) 4.385,1.875 5.917,2.5 1.531,0.625 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) refer to Service Bulletin.

·

After performing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Powertrain > Hybrid Control > Trouble Codes
50001 397
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 440 2
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) AND BODY GROUND)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H7 security indicator light (combination meter assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-25 (IND) - H7-7 (LP) Always Below 1 Ω
H46-25 (IND) or H7-7 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H46 certification ECU (smart key ECU assembly) connector.


b.

Connect the H7 security indicator light (combination meter assembly) connectors.


c.
B574624C15
1.583,0.042 1.979,0.25 0.396,0.208 2.26,1.865 2.135,1.865 2.135,1.865 1.844,0.938 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.667,0.073 1.979,0.271 0.313,0.198 10 false H46 2.323,1.781 2.688,1.969 0.365,0.188 10 false IND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Specified Condition
H46-25 (IND) - Body ground Ignition switch off → ON Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)