| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B000112 | Driver Frontal Stage 1 Deployment Control Circuit Short to Battery | ·
The airbag sensor assembly detects a short to B+ in the driver seat airbag squib circuit for 0.5 seconds ·
Spiral cable sub-assembly malfunction ·
Horn button assembly malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
Spiral cable sub-assembly ·
Horn button assembly ·
Airbag sensor assembly |
Comes on | Applies to check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
To perform the simulation method, select Check Mode with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| Current B000112 is output | A |
| History B000112 is output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.
The connectors are properly connected.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Wire Harness |
Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector and spiral cable sub-assembly connector are not deformed or damaged.
The short springs are not deformed or damaged.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Horn Button Assembly) |
| *b | Color: Light Green |
Connect the connectors to the airbag sensor assembly and spiral cable sub-assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E (light green connector).
Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B000112 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B000112 is not output | A |
| B000112 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect SST from connector E.
A
B
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Wire Harness |
| *a | Front view of wire harness connector
(to Horn Button Assembly) |
| *b | Color: Light Green |
Disconnect the connector from the airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Ignition switch ON | Below 1 V |
| z3-1 - Body ground | Ignition switch ON | Below 1 V |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
Connect the connectors to the horn button assembly and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B000112 may be output at this time, but they are not related to this check.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| B000112 is not output | A |
| B000112 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B
Pre-procedure1
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Wire Harness |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Disconnect the connector from the spiral cable sub-assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Post-procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H38-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| H38-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG