Home › General › MAINTENANCE › REAR DRUM BRAKE SHOE › 2020.03–2020.07
RM36W0E _V1 General _088300 MAINTENANCE _0425223 REAR DRUM BRAKE SHOE A

MAINTENANCE  REAR DRUM BRAKE SHOE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear brake shoe removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

NOTICE:
·

Immediately after installing the brake shoes, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the brake shoes, the brake pedal may feel soft due to clearance between the rear brake shoe and brake drum. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the brake shoes, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
for HV Model:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


Hide 58912C 6.REMOVE NO. 2 BOX SIDE PANEL

Hide 58903A 7.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY

Hide 58857A 8.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET

Hide 9.LOOSEN PARKING BRAKE CABLE

C430601C03
2.99,1.021 2.667,1.208 true 3.01,0.917 3.24,1.115 0.229,0.198 10 true *1
*1 No. 1 Wire Adjusting Nut


a.

Loosen the No. 1 wire adjusting nut

NOTICE:

Do not reuse the loosened No. 1 wire adjusting nut.



Hide 42431D 10.REMOVE BRAKE DRUM

a.

Release the parking brake and remove the brake drum.

HINT:

If the brake drum cannot be removed easily, perform the following procedure.



b.
C434839C01
1.698,1.323 2.323,0.906 true 2.354,0.781 2.573,0.969 0.219,0.188 10 true *1
*1 No. 1 Wire Adjusting Nut


Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.


c.

Using another screwdriver, contract the brake shoe by turning the adjusting bolt.


Hide 04495 11.REMOVE REAR BRAKE SHOE KIT

a.
C434843N01
1.083,1.344 1.469,1.385 true 0.74,1.281 1.094,1.479 0.354,0.198 10 true SST

Using SST, separate the shoe return spring from the front brake shoe.

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



b.
C430602

Using needle-nose pliers, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and front brake shoe.


c.

Remove the tension spring.


d.
C108970

Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.


e.
C430603

Using needle-nose pliers, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and rear brake shoe.


f.
C108972

Using a needle-nose plier, separate the No. 3 parking brake cable assembly.


Hide 47644A 12.REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER

a.
C233135

Remove the automatic adjust lever tension spring and remove the automatic adjust lever.