Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2020.03–2020.07
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0425249 PARKING SUPPORT BRAKE SYSTEM U

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


E220917E83
3.375,0.219 3.74,0.458 0.365,0.24 3.438,0.25 3.896,0.448 0.458,0.198 10 false O60

a.

Disconnect the O60 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O60-1 (IG) - O60-31 (E) IG power source signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
O60-31 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the O60 clearance warning ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O60-2 (BOF) - O60-31 (E) Power source for front sensor circuit
·

Ignition switch ON

·

Parking support brake system on


11 to 14 V
O60-4 (SOF) - O60-31 (E) Front sensor communication signal (Front clearance sonar sensor)
·

Ignition switch ON

·

Parking support brake system on

·

Shift lever in any position other than P

·

Vehicle speed is less than approximately 10 km/h (6 mph)


Pulse generation
(Refer to waveform 1)
O60-3 (E5) - O60-31 (E) Ground for front clearance sonar Always Below 1 Ω
O60-9 (CBZ) - O60-8 (EF) No. 1 clearance warning buzzer signal Buzzer sounding Pulse generation
(Refer to waveform 2)
O60-19 (BOR) - O60-31 (E) Power source for rear sensor circuit
·

Ignition switch ON

·

Parking support brake system on


11 to 14 V
O60-21 (SOR) - O60-31 (E) Rear sensor communication signal (Rear clearance sonar sensor)
·

Ignition switch ON

·

Parking support brake system on

·

Shift lever in R


Pulse generation
(Refer to waveform 3)
O60-20 (E1) - O60-31 (E) Ground for rear clearance sonar Always Below 1 Ω


e.

Using an oscilloscope, check waveform 1.

i.
E434397N02
0.156,1 0.615,1.198 0.458,0.198 10 false 11 V

Waveform 1 (Reference)

Item Content
Measurement terminal O60-4 (SOF) - O60-31 (E)
Measurement setting 1 V/DIV., 100 μs./DIV.
Condition
·

Ignition switch ON

·

Parking support brake system on

·

Shift lever in any position other than P

·

Vehicle speed is less than approximately 10 km/h (6 mph)





f.

Using an oscilloscope, check waveform 2.

i.
E227014N05
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 2 (Reference)

Item Content
Measurement terminal O60-9 (CBZ) - O60-8 (EF)
Measurement setting 2 V/DIV., 500 μs./DIV.
Condition Buzzer sounding

HINT:

The amplitude of the waveform changes according to the set volume.




g.

Using an oscilloscope, check waveform 3.

i.
E434397N03
0.156,1 0.615,1.198 0.458,0.198 10 false 11 V

Waveform 3 (Reference)

Item Content
Measurement terminal O60-21 (SOR) - O60-31 (E)
Measurement setting 1 V/DIV., 100 μs./DIV.
Condition
·

Ignition switch ON

·

Parking support brake system on

·

Shift lever in R









BLIND SPOT MONITOR SENSOR RH (A) (w/ Blind Spot Monitor System)


Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU


BLIND SPOT MONITOR SENSOR LH (B) (w/ Blind Spot Monitor System)


Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU