Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2020.03–2020.07
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0425251 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB511  Outer Mirror Indicator (Module "A" Side) Circuit Short to Ground  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (A) detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB511 Outer Mirror Indicator (Module "A" Side) Circuit Short to Ground
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH (A)



WIRING DIAGRAM

E270468E70
3.073,1.479 3.229,1.677 0.156,0.198 10 false 2 3.063,1.875 3.219,2.073 0.156,0.198 10 false 1 2.844,1.563 3,1.76 0.156,0.198 10 false + 2.802,1.948 2.958,2.146 0.156,0.198 10 false - 1.146,2.396 1.802,2.625 0.656,0.229 10 false A 1.135,2.573 2.854,2.969 1.719,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.438,3.708 2.771,4.104 2.333,0.396 10 false Outer Rear View Mirror Assembly RH 3.438,1.448 3.906,1.646 0.469,0.198 10 false BSR+ 5.427,1.594 5.896,1.792 0.469,0.198 10 false OMIR 5.219,1.479 5.688,1.677 0.469,0.198 10 false 4 5.365,3.563 5.833,3.76 0.469,0.198 10 false S6 5.354,3.75 6.583,4.375 1.229,0.625 10 false Blind Spot Monitor Sensor RH (A) 3.885,1.458 4.115,1.646 0.229,0.188 10 false 8 3.885,1.906 4.156,2.073 0.271,0.167 10 false 15 3.708,1.896 3.948,2.063 0.24,0.167 10 false - 0.448,3.563 0.917,3.76 0.469,0.198 10 false K8

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the blind spot monitor sensor RH (A) connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E395851C29
0.229,0.938 0.594,1.25 0.365,0.313 2.313,1.156 2.656,1.406 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.313,1.01 0.625,1.208 0.313,0.198 10 false K8 2.708,1.365 3.198,1.552 0.49,0.188 10 false BSR+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the A outer mirror RH (outer rear view mirror indicator RH).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K8-8 (BSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

OK

NG

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)