Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C050623  Right Front Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C05061F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C05061F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050623 Right Front Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.


·

Front speed sensor RH

·

Speed sensor installed improperly

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Wire harness or connector


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE

·

After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 Nm
*d No clearance


Turn the ignition switch off.


b.

Check the front speed sensor RH installation.

OK:

There is no clearance between the front speed sensor RH and front axle carrier sub-assembly.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

2.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the front speed sensor RH tip.

OK:

The front speed sensor RH tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.

·

If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FR WHEEL SPEED)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH

3.READ VALUE USING GTS (FR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
50003 435 13

b.

Check the front speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A23 front speed sensor RH connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-1 (FR+) - A38-3 (FR+) Always Below 1 Ω
A23-1 (FR+) or A38-3 (FR+) - Body ground Always 10 kΩ or higher
A23-2 (FR-) - A38-4 (FR-) Always Below 1 Ω
A23-2 (FR-) or A38-4 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the front speed sensor rotor RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor rotor RH.

OK:

The front speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.

·

Do not use parts cleaner when cleaning the front speed sensor rotor RH.

·

If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.



HINT:
·

The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.

·

If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.




Result:
Result Proceed to
OK A
NG (The front speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the front speed sensor rotor RH.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

C

CLEAN FRONT SPEED SENSOR ROTOR RH