The skid control ECU (brake booster with master cylinder assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.
The skid control ECU (brake booster with master cylinder assembly) incorporates a circuit to detect an open circuit.
This DTC is output when an open circuit is detected in the stop light signal input line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| P057113 | Brake Switch "A" Circuit Open | An open stop light switch circuit continues for 10 seconds or more. | ·
Wire harness or connector ·
Stop light switch assembly ·
Skid control ECU (brake booster with master cylinder assembly) ·
Stop light circuit |
Brake |
Refer to DTCs C13807E.
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the skid control ECU (brake booster with master cylinder assembly), perform calibration (linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
Check that the stop lights come on when the brake pedal is depressed.
| Result | Proceed to |
|---|---|
| All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. | A |
| All stop lights do not illuminate when the brake pedal is depressed. | B |
| One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. | C |
A
B
C
Check the value of Stop Light SW when the brake pedal is depressed.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly status | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Tester Display |
|---|
| Stop Light SW |
| Result | Proceed to |
|---|---|
| The value of Stop Light SW is ON. | A |
| Other than above. | B |
A
B
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (OUT) - Body ground | ·
Ignition switch ON ·
The headlights are on ·
The blower motor switch is in the HI position ·
The rear window defogger is turned on ·
Stop light switch assembly off (Brake pedal released) |
Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| P057113 is not output | A |
| P057113 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A63 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there is no short to +B in the STP circuit (wire harnesses, connectors, ECUs and stop lights).
No short to +B.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-12 (STP) - Body ground | Stop light switch assembly on
(Brake pedal depressed) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.
No open.
| Proceed to |
|---|
| OK |
| NG |
OK
NG