The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.
The skid control ECU (brake booster with master cylinder assembly) turns on the brake system warning light (red indicator) and brake system warning light (yellow indicator), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.
DTC C125600 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C125600 | Accumulator Low Pressure Abnormality | Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.) |
·
Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction) ·
Pump motor malfunction ·
Accumulator deterioration ·
Accumulator pressure sensor (brake booster with master cylinder assembly) ·
Supply voltage reduced |
Brake |
Refer to DTC C059400.
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only C125600 is output | A |
| None of the above conditions are met | B |
A
B
| *a | Component without harness connected
(Brake Booster Pump Assembly) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A30 brake booster pump assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (BM1) - 4 (GND1) | Always | 10 Ω or less |
| 1 (BM2) - 3 (GND2) | Always | 10 Ω or less |
| 2 (BM1) - 1 (BM2) | Always | Below 1 Ω |
| 4 (GND1) - 3 (GND2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A30 brake booster pump assembly connector.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa, Max.: 24.48 MPa | 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped) |
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Tester Display |
|---|
| MTT |
| Accumulator Pressure |
Depress the brake pedal several times to operate the pump motor, then wait until it stops.
After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.
| Result | Proceed to |
|---|---|
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds | A |
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Reconnect the A27 brake pedal stroke sensor assembly connector.
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB Solenoid (SLR) | Linear solenoid reduction valve (SLR) | Solenoid ON/OFF | ECB: Electronically Controlled Brake System |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa, Max.: 24.48 MPa | Brake pedal released: 0.00 to 2.10 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Active Test Display |
|---|
| ECB Solenoid (SLR) |
| Data List Display |
|---|
| Servo Pressure |
Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).
Check that the servo pressure output value does not increase when performing the Active Test.
The servo pressure output value does not increase when performing the Active Test.
If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.
| Result | Proceed to |
|---|---|
| The servo pressure output value increases. | A |
| The servo pressure output value does not increase. | B |
A
B
for Brake Booster with Master Cylinder Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model)>REMOVAL
for Brake Booster Pump Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL