Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The yaw rate sensor has a built-in acceleration sensor.

The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U012587 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


These DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Acceleration sensor zero point calibration is incomplete.
·

Acceleration sensor (airbag sensor assembly) installed improperly

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C121054 Yaw Rate Sensor Missing Calibration Yaw rate sensor zero point calibration is incomplete.
·

Yaw rate sensor (airbag sensor assembly) installed improperly

·

Yaw rate sensor (airbag sensor assembly)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C051D54 or C121054 is output A
None of the above conditions are met B



A

3.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

B

3.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

4.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
4.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not tilted.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and Rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/ deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s,
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29

b.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG