Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the ignition switch is turned to ON while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

Steering Unlock Request Receive

·

L Code Check



WIRING DIAGRAM

B463111E21
3.552,0.563 5.198,0.875 1.646,0.313 10 false from Auxiliary Battery 2.583,0.74 3.5,0.938 0.917,0.198 10 false AM1 5.354,3.313 6.885,3.823 1.531,0.51 10 false Certification ECU (Smart Key ECU Assembly) 0.646,4.365 2.635,4.583 1.99,0.219 10 false : LIN Communication Line 5.344,3.156 6,3.49 0.656,0.333 10 false H46 0.188,3.177 1.104,3.375 0.917,0.198 10 false H71 0.188,3.323 3,3.948 2.813,0.625 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 1.802,1.844 2.719,2.042 0.917,0.198 10 false IGE 1.698,2.281 2.615,2.479 0.917,0.198 10 false SLP1 1.76,2.75 2.677,2.948 0.917,0.198 10 false GND 2.156,0.458 2.646,0.708 0.49,0.25 10 false 7 5.771,2.729 6.26,2.948 0.49,0.219 10 false E 5.771,2.302 6.26,2.521 0.49,0.219 10 false SLP 5.76,1.823 6.25,2.042 0.49,0.219 10 false SLR+ 5.5,1.74 5.99,1.958 0.49,0.219 10 false 24 5.5,2.177 5.99,2.396 0.49,0.219 10 false 11 5.521,2.625 6.01,2.844 0.49,0.219 10 false 29 1.948,0.552 2.438,0.802 0.49,0.25 10 false B 2.146,1.719 2.635,1.969 0.49,0.25 10 false 3 2.146,2.177 2.635,2.427 0.49,0.25 10 false 4 2.146,2.625 2.635,2.875 0.49,0.25 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P (for CVT), and then open a door.


·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not recur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

·

If the steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the ignition switch off, and then unlock the steering by pressing the engine switch.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the electrical key transmitter sub-assembly is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows *1:


ii.

When the electrical key transmitter sub-assembly is inside the vehicle, check that pressing the engine switch with the clutch pedal released causes the power source mode to change as follows *2:

*1: for CVT

*2: for Manual Transaxle


OK:

Off → ACC → ON → Off




Result:
Proceed to
OK
NG



OK

2.CHECK MULTI-INFORMATION DISPLAY

NG

2.CHECK MULTI-INFORMATION DISPLAY
a.

With the ignition switch ON, check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
Steering Lock active is displayed A
Steering Lock active is not displayed B



A

3.CHECK STEERING UNLOCK

B

4.CHECK FOR DTC
3.CHECK STEERING UNLOCK
a.

Turn the steering wheel left and right, and then press the engine switch.


b.

Check that the steering is unlocked.


Result:
Result Proceed to
The steering is unlocked A
The steering is not unlocked B



A

END (STEERING LOCK NORMAL)

B

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
NOTICE:

If a malfunction occurs, do not remove/install the vehicle auxiliary battery before checking for DTCs.


OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

5.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds of turning the ignition switch to ACC or ON or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (L CODE CHECK)

NG

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
6.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)

NG

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C342408C96
1.552,0.875 2,1.135 0.448,0.26 0.792,3.052 0.979,3.052 0.979,3.052 1.219,2.469 true 2.583,3.052 2.406,3.052 2.406,3.052 2.156,2.49 true 0.188,0.094 0.5,0.25 0.313,0.156 10 false *a 0.5,2.969 0.958,3.167 0.458,0.198 10 false GND 1.646,0.927 2.104,1.125 0.458,0.198 10 false H71 2.635,2.99 3.094,3.188 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C396300C15
0.323,2.906 1.646,3.042 1.323,0.135 2.344,2.948 2.75,3.073 0.406,0.125 1.615,4.063 2.375,4.177 0.76,0.115 1.531,0.177 1.969,0.406 0.438,0.229 0.896,3.25 0.896,3.042 false 2.573,3.281 2.573,3.073 false 2.01,4.063 2.01,3.854 false 0.813,1.802 1.875,1.104 true 2.792,1.646 2.302,1.083 true 0.271,0.26 0.583,0.417 0.313,0.156 10 false *a 0.823,3.281 1.135,3.438 0.313,0.156 10 false *b 1.917,3.688 2.229,3.844 0.313,0.156 10 false *c 2.5,3.302 2.813,3.458 0.313,0.156 10 false *b 0.646,1.854 1.104,2.052 0.458,0.198 10 false IGE 2.76,1.698 3.219,1.896 0.458,0.198 10 false GND 2.969,4.083 3.427,4.281 0.458,0.198 10 false GND 1.635,0.219 2.094,0.417 0.458,0.198 10 false H71
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Content
Tester Connection H71-3 (IGE) - H71-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Ignition switch turned off



*1: for CVT



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-3 (IGE) - H46-24 (SLR+) Always Below 1 Ω
H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C342409C46
1.531,0.844 2.01,1.125 0.479,0.281 1.917,1.938 2.667,2.656 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.646,0.906 1.958,1.063 0.313,0.156 10 false H71 2.615,2.708 2.917,2.885 0.302,0.177 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) inthe table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-3 (IGE) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C400234C70
1.51,0.917 1.885,1.167 0.375,0.25 2.302,2.979 1.719,2.979 1.719,2.979 1.719,1.979 true 2.344,2.896 2.802,3.094 0.458,0.198 10 false SLP1 1.573,0.958 2.031,1.156 0.458,0.198 10 false H71 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-4 (SLP1) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

14.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
13.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Turn the ignition switch to ON.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds after the ignition switch is turned to ACC or ON or the engine is started, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

14.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-4 (SLP1) - H46-11 (SLP) Always Below 1 Ω
H71-4 (SLP1) or H46-11 (SLP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



c.

Turn the ignition switch to ON.


d.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds of turning the ignition switch to ACC or ON or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)