Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279F1C  Steering Lock Confirmation Signal Circuit Voltage Out of Range  


DESCRIPTION

This DTC is stored when the SLA input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.

HINT:

The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279F1C Steering Lock Confirmation Signal Circuit Voltage Out of Range Either of the following conditions is met (1-trip detection logic*):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Any time



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not start).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B279F1C -

WIRING DIAGRAM

B463087E28
0.875,3.375 2.677,3.688 1.802,0.313 10 false : LIN Communication Line 5.552,2.635 7.063,2.99 1.51,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.552,2.469 6.177,2.75 0.625,0.281 10 false H46 5.99,0.344 6.573,0.552 0.583,0.208 10 false SLA1 5.771,0.219 6.115,0.542 0.344,0.323 10 false 3 1.885,0.219 2.229,0.542 0.344,0.323 10 false 6 1.479,0.313 1.823,0.635 0.344,0.323 10 false SLA 1.438,2.042 1.781,2.365 0.344,0.323 10 false GND 1.896,1.938 2.24,2.26 0.344,0.323 10 false 1 0.104,2.49 1.771,2.896 1.667,0.406 10 false H71 0.094,2.656 2.76,3.188 2.667,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until ommunication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check if LIN communication DTC B278588 is output.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278588 is not output A
DTC B278588 is output B



A

2.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

B

GO TO LIN COMMUNICATION SYSTEM (DTC B278588)

2.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-6 (SLA) - H71-1 (GND) Ignition switch off Below 1 V
H71-6 (SLA) - H71-1 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
3.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B279F1C is output.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B279F1C is output A
DTC B279F1C is not output B



A

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

B

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-6 (SLA) - H46-3 (SLA1) Always Below 1 Ω
H71-6 (SLA) or H46-3 (SLA1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR