The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B142A88 | Servo Motor LIN Communication Bus off | Diagnosis Condition:
Ignition switch ON Malfunction Status: Error or lost communication with each servo motor Detection Time: Continuously for 10 seconds or more |
·
Air conditioning harness assembly ·
No. 1 air conditioning radiator damper servo sub-assembly ·
Air conditioning amplifier assembly |
Memorized |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction | Error communication with each servo motor | ○ | - |
| Lost communication with each servo motor | - | ○ | |
| Detection Time | Continuously for 10 seconds or more | Continuously for 10 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions of either of these patterns are detected, a DTC will be stored
for Dual Type
for Single Type
This DTC is also output when servomotor initialization has failed. When servomotor initialization has failed, repair any malfunctions and perform servomotor initialization again.
When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.
Pre-procedure1
Disconnect the air conditioning amplifier assembly connector.
Procedure1
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h6-4 (BUSB) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h6-2 (BUSG) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. | h6-3 (BUS) ←→ h6-2 (BUSG) |
| Tool Setting | 2 V/DIV., 2 ms./DIV. |
| Condition | Ignition switch ON |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Pre-procedure1
Disconnect the h7 No. 1 air conditioning radiator damper servo sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h6-2 (BUSG) - h7-6 (GND) | Always | Below 1 Ω |
| h6-3 (BUS) - h7-7 (LIN) | Always | Below 1 Ω |
| h6-4 (BUSB) - h7-8 (+B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the h7 No. 1 air conditioning radiator damper servo sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h6-2 (BUSG) - h7-6 (GND) | Always | Below 1 Ω |
| h6-3 (BUS) - h7-7 (LIN) | Always | Below 1 Ω |
| h6-4 (BUSB) - h7-8 (+B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG