Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System) › from 2020.07
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0420297 AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System) Y

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the air conditioning system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Inspect the auxiliary battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

5.CHECK COMMUNICATION FUNCTION OF CXPI COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF CXPI COMMUNICATION SYSTEM*
a.

Using the GTS, check for CXPI communication system DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
CXPI communication system DTCs are not output A
CXPI communication system DTCs are output B



A

6.CHECK POWER INTEGRATION SYSTEM*

B

6.CHECK POWER INTEGRATION SYSTEM*
a.

Using the GTS, check for power integration system DTCs.

Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.CHECK VEHICLE CONTROL HISTORY (RoB)*

B

7.CHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Using the GTS, check for vehicle control history (RoB).

Body Electrical > Air Conditioner > Utility
Tester Display
Vehicle Control History (RoB)
50005 450 55

b.

Record the vehicle control history.


Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

8.CHECK FOR DTC*

B

8.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Body Electrical > Air Conditioner > Trouble Codes
50001 450

b.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 450

c.

Recheck for DTCs. Based on the DTCs output above, try to force output of the air conditioning system DTC by simulating the operation indicated by the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 450

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

9.CHECK HEATER CONTROL SUB-ASSEMBLY

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

9.CHECK HEATER CONTROL SUB-ASSEMBLY
a.

Operate each switch and check that the air conditioning system operates normally.


Result:
Proceed to
OK
NG



OK

10.CHECK BLOWER CONTROL

NG

10.CHECK BLOWER CONTROL
a.

Operate the blower switch on the No. 2 heater control sub-assembly and check that the blower control operates normally.


Result:
Proceed to
OK
NG



OK

11.CHECK AIR INLET CONTROL

NG

11.CHECK AIR INLET CONTROL
a.

Operate the recirculation/fresh switch on the No. 2 heater control sub-assembly and check that the air inlet control operates normally.


Result:
Proceed to
OK
NG



OK

12.CHECK AIR OUTLET CONTROL

NG

12.CHECK AIR OUTLET CONTROL
a.

Operate the airflow mode control switch on the No. 1 heater control sub-assembly and check that the air outlet control operates normally.


Result:
Proceed to
OK
NG



OK

13.CHECK COOLING FUNCTION

NG

13.CHECK COOLING FUNCTION
a.

Operate the temperature control switches on the No. 3 heater control sub-assembly and check that cool air is blown from the registers.


Result:
Proceed to
OK
NG



OK

14.CHECK HEATER FUNCTION

NG

14.CHECK HEATER FUNCTION
a.

Operate the temperature control switches on the No. 3 heater control sub-assembly and check that warm air is blown from the air registers.


Result:
Proceed to
OK
NG



OK

15.USE SIMULATION METHOD TO CHECK

NG

15.USE SIMULATION METHOD TO CHECK

NEXT

16.CONFIRMATION TEST
16.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END