Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD) › 2020.07–2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0430792 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch pedal sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 84520 2.REMOVE CLUTCH START SWITCH ASSEMBLY

Hide 31453A 3.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

a.
C431220

Remove the clip from the clevis pin.


b.

Remove the master cylinder push rod clevis with hole pin to disconnect the clutch master cylinder assembly from the clutch pedal sub-assembly.


Hide 4.REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY

a.
C439397

Disconnect the clutch switch assembly connector.


b.

Disengage the 2 clamps to disconnect the wire harness from the clutch pedal support assembly.


c.
C436224

Remove the 4 nuts and clutch pedal support assembly from the vehicle body.


Hide 88280A 5.REMOVE CLUTCH SWITCH ASSEMBLY

Hide 31301A 6.REMOVE CLUTCH PEDAL SPRING (except 1KR-FE)

a.
C431223

Move the clutch pedal sub-assembly to the full stroke position.


b.

Remove the clutch pedal spring from the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.


Hide 31301 7.REMOVE CLUTCH PEDAL SUB-ASSEMBLY

a.

Mount the clutch pedal sub-assembly in a soft jaw vise.

NOTICE:

Be careful not to damage the clutch pedal sub-assembly in the vise.



b.
C431224

Remove the bolt, nut, clutch pedal sub-assembly from the clutch pedal support sub-assembly.


Hide 31353 8.REMOVE CLUTCH PEDAL SPRING HOLDER (except 1KR-FE)

a.
C431225

Remove the clutch pedal spring holder from the clutch pedal support sub-assembly.


Hide 31301P 9.REMOVE CLUTCH PEDAL TURNOVER BUSH (except 1KR-FE)

a.
C431226

Remove the clutch pedal turnover bushing from the clutch pedal sub-assembly.


Hide 31324A 10.REMOVE CLUTCH PEDAL SHAFT COLLAR

a.
C431227

Remove the 2 clutch pedal bushings from the clutch pedal sub-assembly.


b.
C431228

Remove the clutch pedal shaft collar from the clutch pedal sub-assembly.


Hide 31453B 11.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

a.
C431236C01
2.5,2 2.5,1.438 false 2.25,2 2.833,2 2.833,2 2.833,1.667 false 0.302,0.302 0.531,0.5 false 1.938,1.906 2.396,2.104 0.458,0.198 10 false SST 0.104,0.177 0.563,0.375 0.458,0.198 10 false *a
*a Clutch Master Cylinder Push Rod Clevis Bushing


Using SST and a hammer, remove the clutch master cylinder push rod clevis bushing from the clutch pedal sub-assembly.

SST
09201-01055  
09950-70010  (09951-07100)


Hide 31321 12.REMOVE CLUTCH PEDAL PAD

a.
C431229

Remove the clutch pedal pad from the clutch pedal sub-assembly.