Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.07–2021.11
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P060A94  Hybrid/EV Powertrain Control Module Monitoring Processor Unexpected Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The main CPU and sub CPU of the hybrid vehicle control ECU monitor their internal operation and each other for malfunctions.

The cause of this malfunction may be the following:

Hybrid vehicle control ECU internal malfunction
·

Hybrid vehicle control ECU malfunction


Vehicle speed sensor malfunction
·

Discrepancy between motor resolver signal and actual vehicle speed



DESCRIPTION

The hybrid vehicle control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P060A94 Hybrid/EV Powertrain Control Module Monitoring Processor Unexpected Operation
·

The sub CPU value received by the main CPU of the hybrid vehicle control ECU exceeds the threshold for a certain period of time.

·

The hybrid vehicle control ECU detects an internal malfunction due to an abnormal calculation or sensor malfunction.


(1 trip detection logic)
Hybrid vehicle control ECU Comes on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 10 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (MOTOR GENERATOR)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
No DTCs are output, or DTCs except the ones in the table below are also output A
Any of the following DTCs are also output B


Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F21 Drive Motor "A" Position Sensor Signal Amplitude < Minimum
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum

HINT:
·

P060A94 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (BRAKE)

B

2.CHECK DTC OUTPUT (BRAKE)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs are output A
DTCs are not output B



Post-procedure1

c.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P060A94 and other DTCs are output A
Only P060A94 is output B



Post-procedure1

c.

Turn the ignition switch off.



A

B

4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Read the freeze frame data of DTC P060A94.

Powertrain > Hybrid Control > DTC(P060A94) > Freeze Frame Data
Tester Display
Vehicle Speed
FR Wheel Speed
FL Wheel Speed
50040 397 12,104,105 P060A94
HINT:
·

Vehicle stopped.

·

"FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph).



Result:
Result Proceed to
The value of Vehicle Speed is 3 km/h or more A
The value of Vehicle Speed is less than 3 km/h B


HINT:

3 km/h (2mph)



Post-procedure1

c.

Turn the ignition switch off.



A

GO TO MOTOR RESOLVER CIRCUIT

For the inspection method of the motor resolver circuit, refer to DTC P0A3F16.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0A3F16


B