Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2A11  Drive Motor "A" Temperature Sensor Circuit Short to Ground  P0A2A15  Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU malfunction
·

Hybrid vehicle control ECU internal malfunction


Motor temperature sensor malfunction
·

Motor temperature sensor internal malfunction

·

Open or short in motor temperature sensor


Wire harness between the motor temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in the motor (MG2) temperature. The lower the motor (MG2) temperature, the higher the thermistor resistance. Conversely, the higher the motor (MG2) temperature, the lower the resistance.

HINT:

The term "drive motor A" indicates the motor (MG2).


C189867E22
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A2A11 Drive Motor "A" Temperature Sensor Circuit Short to Ground Short to ground in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Motor temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning: Comes on
P0A2A15 Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open Open or short to +B in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Motor temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P0A2A11 Motor Temperature
P0A2A15

HINT:

After confirming that DTC P0A2A11 or P0A2A15 is output, use the GTS to check "Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A458545E15
1.74,0.927 2.198,1.125 0.458,0.198 10 false MMT 1.625,1.667 2.125,1.896 0.5,0.229 10 false MMTG 2.167,0.927 2.344,1.115 0.177,0.188 10 false 1 2.177,1.677 2.438,1.854 0.26,0.177 10 false 2 0.229,2.406 0.688,2.604 0.458,0.198 10 false D59 0.24,2.573 2.302,3.104 2.063,0.531 10 false Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly) 2.646,2.25 3.104,2.448 0.458,0.198 10 false DA2 2.646,2.438 4.656,3.042 2.01,0.604 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly Connector 4.938,2.458 5.396,2.656 0.458,0.198 10 false A68 4.927,2.625 6.792,2.969 1.865,0.344 10 false Hybrid Vehicle Control ECU 4.865,0.938 5.323,1.135 0.458,0.198 10 false MMT 4.865,1.667 5.427,1.875 0.563,0.208 10 false MMTG 5.948,1.042 6.365,1.229 0.417,0.188 10 false ADC 3.698,0.917 3.865,1.115 0.167,0.198 10 false 7 3.677,1.677 3.906,1.854 0.229,0.177 10 false 17 4.604,0.927 4.823,1.115 0.219,0.188 10 false 43 4.594,1.677 4.833,1.865 0.24,0.188 10 false 44 3.073,0.917 3.24,1.115 0.167,0.198 10 false 7 3.021,1.667 3.25,1.844 0.229,0.177 10 false 17

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Check the connection condition of the hybrid vehicle control ECU connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


A470188C02
0.146,0.042 0.458,0.24 0.313,0.198 10 false *A 3.833,0.042 4.146,0.24 0.313,0.198 10 false *B
*A for RHD *B for LHD


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C




A

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)
a.

Check that the intermediate connector which connects the motor temperature sensor to the hybrid vehicle control ECU is securely connected with no deformation, and that there is no contamination by water or foreign matter.

HINT:
·

For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.



OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)
a.
A458482

Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

4.READ VALUE USING GTS (MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (MOTOR TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

b.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temperature
50003 397 66
Result:
Result Proceed to
The value of Motor Temperature is -40°C A
The value of Motor Temperature is 215°C B
None of the above conditions are met C


HINT:
·

-40°C (-40°F)

·

215°C (419°F)




Post-procedure1

c.

Turn the ignition switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A458482N01
2.573,0.76 3,1.052 0.427,0.292 2.667,0.833 2.938,1.01 0.271,0.177 10 true D59

Disconnect the D59 motor temperature sensor connector.


Procedure1

b.
A385118C70
1.469,0.281 1.958,0.635 0.49,0.354 1.854,1.76 1.875,1.323 true 2.427,1.792 2.115,1.323 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 2.354,1.833 2.781,2.063 0.427,0.229 10 false MMT 1.708,1.844 2.188,2.052 0.479,0.208 10 false MMTG 1.615,0.396 2.073,0.594 0.458,0.198 10 false D59
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D59-1 (MMT) - D59-2 (MMTG) Ignition switch off 0.3443 to 1446 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.


Result:
Proceed to
OK
NG



Post-procedure1

c.

Reconnect the D59 motor temperature sensor connector.



OK

6.INSPECT HYBRID VEHICLE CONTROL ECU

NG

6.INSPECT HYBRID VEHICLE CONTROL ECU

Pre-procedure1

a.

Connect terminals 43 (MMT) and 44 (MMTG) of the A68 hybrid vehicle control ECU connector.

A458550C03
2.438,0.26 2.875,0.563 0.438,0.302 2.635,1.635 3.198,2.417 true 2.479,1.635 1.979,2.396 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 2.552,0.344 3.01,0.542 0.458,0.198 10 false A68 1.573,2.417 2.063,2.667 0.49,0.25 10 false MMTG 3.229,2.417 3.844,2.615 0.615,0.198 10 false MMT
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -



Procedure1

b.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temperature
50003 397 66
OK:
Tester Display Condition Specified Condition
Motor Temperature Terminals A68-43 (MMT) and A68-44 (MMTG) connected
Ignition switch ON
215°C (419°F)


Result:
Result Proceed to
The value of Motor Temperature is 215°C A
None of the above conditions are met B



Post-procedure1

c.

Turn the ignition switch off.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A458482N01
2.573,0.76 3,1.052 0.427,0.292 2.667,0.833 2.938,1.01 0.271,0.177 10 true D59

Disconnect the D59 motor temperature sensor connector.


Procedure1

b.
A385118C70
1.469,0.281 1.958,0.635 0.49,0.354 1.854,1.76 1.875,1.323 true 2.427,1.792 2.115,1.323 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 2.354,1.833 2.781,2.063 0.427,0.229 10 false MMT 1.708,1.844 2.188,2.052 0.479,0.208 10 false MMTG 1.615,0.396 2.073,0.594 0.458,0.198 10 false D59
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D59-1 (MMT) - D59-2 (MMTG) Ignition switch off 0.3443 to 1446 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.


Result:
Proceed to
OK
NG



Post-procedure1

c.

Reconnect the D59 motor temperature sensor connector.



OK

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

Pre-procedure1

a.

Disconnect the D59 motor temperature sensor connector.


b.

Disconnect the A68 hybrid vehicle control ECU connector.


Procedure1

c.
A458546C01
1.521,0.229 1.927,0.5 0.406,0.271 1.51,2.156 1.917,2.438 0.406,0.281 1.688,1.615 1.563,1.135 true 1.219,1.615 1.406,1.135 true 1.719,4.167 1.906,3.688 true 2.271,4.167 2.073,3.688 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.208,2.219 0.521,2.417 0.313,0.198 10 false *b 1.615,0.292 1.927,0.49 0.313,0.198 10 false D59 1.604,2.229 1.917,2.427 0.313,0.198 10 false A68 1.021,1.656 1.479,1.885 0.458,0.229 10 false MMT 1.531,1.656 1.99,1.885 0.458,0.229 10 false MMTG 2.271,4.208 2.729,4.438 0.458,0.229 10 false MMTG 1.469,4.208 1.927,4.438 0.458,0.229 10 false MMT
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D59-1 (MMT) - A68-43 (MMT) Ignition switch off Below 1 Ω
D59-2 (MMTG) - A68-44 (MMTG) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D59-1 (MMT) or A68-43 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
D59-2 (MMTG) or A68-44 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Reconnect the A68 hybrid vehicle control ECU connector.


e.

Reconnect the D59 motor temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR