Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › 2020.07–2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0430794 CLUTCH PEDAL(for LHD) G

CLUTCH  CLUTCH PEDAL(for LHD)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CLUTCH PEDAL HEIGHT

a.

Remove front door scuff plate.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL

HINT:

Use the same procedure as for the RH side.



b.

Remove cowl side trim board.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL

HINT:

Use the same procedure as for the RH side.



c.

Turn back floor carpet.


d.

Check that the clutch pedal height is correct.

C437865C01
5.917,1.75 6.25,2 0.333,0.25 10 true *a 2.865,1.333 3.198,1.583 0.333,0.25 10 true *a
*a Clutch Pedal Height - -
V100155

Measuring Plane of Floor Panel - -


Pedal height from floor panel:

154.8 to 174.8 mm (6.09 to 6.88 in.)


·

If the result is not as specified, bleed the clutch line and perform the inspection again.

·

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.



e.

Install the floor carpet.


f.

Install cowl side trim board.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION

HINT:

Use the same procedure as for the RH side.



g.

Install front door scuff plate.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION

HINT:

Use the same procedure as for the RH side.



Hide 2.INSPECT CLUTCH PEDAL FREE PLAY

a.
C437866C01
2.958,2.865 3.271,3.021 0.313,0.156 10 false *a
*a Clutch Pedal Free Play


Check that the clutch pedal free play is correct.

HINT:

Pay close attention to the change in resistance to distinguish clutch pedal free play while performing the inspection.


i.

Depress the clutch pedal until clutch resistance begins to be felt.

Clutch pedal free play (Reference):

3 to 15 mm (0.118 to 0.591 in.)


·

If the result is not as specified, bleed the clutch line and perform the inspection again.

·

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.




Hide 3.INSPECT CLUTCH RELEASE POINT

CAUTION:

When checking the clutch release point, ensure that the vehicle is secure.


a.
C227877C11
1.365,1.177 1.615,1.177 false 1.615,1.583 2.281,1.042 2.281,1.042 2.396,1.042 true 1.354,1.521 0.906,1.885 0.906,1.885 0.802,1.885 true 1.396,0.99 1.635,1.198 0.24,0.208 10 false *c 1.802,1.917 2.063,2.125 0.26,0.208 10 false *d 0.646,1.802 0.948,2.052 0.302,0.25 10 false *b 2.458,0.969 2.719,1.198 0.26,0.229 10 false *a
*a Release Point
*b Full Stroke End Position
*c Distance from Clutch Pedal Stroke End Position to Release Point
*d Clutch Pedal Stroke


Check the clutch release point.

i.

Be sure to apply the parking brake and secure the wheels using wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to reverse until the gears contact.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard Distance:

25 mm (0.984 in.) or more (from clutch pedal stroke end position to release point)


Clutch pedal stroke at 200 N (20 kgf, 45.0 lbf):
Reference:

141 to 151 mm (5.55 to 5.94 in.)


If the distance is not as specified, perform the following procedure:

·

Check the clutch pedal height.

·

Check the clutch pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover assembly and the clutch disc assembly.