63311C
1.INSTALL ROOF HEADLINING (for Panoramic Moon Roof)
|
Install in this Direction |
Insert the roof headlining into the cabin from the back door.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Disengage the guides and 12 fasteners to remove the roof headlining.
Disengage the 2 guides.
Install the 2 clips.
for Roof Rear Side:
Engage the guide.
Install the ground wire with the bolt.
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Windshield Glass Side:
Connect the 4 connectors.
for Front Pillar RH Side:
Engage the clamps.
Connect the connector.
for Front Pillar LH Side:
Engage the clamps.
Connect the 2 connectors.
63311C
2.INSTALL ROOF HEADLINING (for Normal Roof)
|
Install in this Direction |
Insert the roof headlining into the cabin from the back door.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Engage the guides to set the roof headlining.
for TMC Made:
Using a clip remover, remove the 2 clips.
for TMMF Made:
Using a clip remover, remove the 4 clips.
for Roof Rear Side:
Engage the guide.
Install the ground wire with the bolt.
Connect the connector.
for Rear Pillar RH Side:
Connect the connector.
for Windshield Glass Side:
for TMC Made:
Connect the 2 connectors.
for TMMF Made with EC Mirror:
Connect the 2 connectors.
for TMMF Made with Toyota Safety Sense 2:
Connect the 3 connectors.
for TMMF Made with Toyota Safety Sense 2 and EC Mirror:
Connect the 4 connectors.
for Front Pillar RH Side:
Engage the clamps.
Connect the connector.
for Front Pillar LH Side:
Engage the clamps.
Connect the 2 connectors.
63339A
3.INSTALL ROOF HEADLINING SERVICE HOLE COVER
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the roof headlining service hole cover as shown in the illustration.
86466D
4.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
86466E
5.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
81340
6.INSTALL VANITY LIGHT ASSEMBLY
81240J
7.INSTALL ROOM LIGHT ASSEMBLY (for TMC Made)
81260A
8.INSTALL MAP LIGHT ASSEMBLY
74612
9.INSTALL ASSIST GRIP COVER
Use the same procedure for all assist grip sub-assemblies.
Install the 2 assist grip covers and 2 clips to the assist grip sub-assembly.
74610A
10.INSTALL ASSIST GRIP SUB-ASSEMBLY
Use the same procedures for the opposite side.
|
Install in this Direction |
Engage the clips to install the assist grip sub-assembly as shown in the illustration.
74630E
11.INSTALL REAR ASSIST GRIP ASSEMBLY LH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
74620C
12.INSTALL REAR ASSIST GRIP ASSEMBLY RH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
13.INSTALL COAT HOOK (w/o Assist Grip)
Use the same procedures for the opposite side.
Engage the clip to install the coat hook.
74348C
14.INSTALL VISOR HOLDER
Use the same procedures for the opposite side.
|
Install in this Direction |
Engage the claws to install the base as shown in the illustration.
|
Install in this Direction |
Install the visor holder as shown in the illustration.
74320
15.INSTALL VISOR ASSEMBLY LH
74310
16.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
62472A
17.INSTALL ROOF SIDE INNER GARNISH LH
|
Install in this Direction |
Engage the clips to install the roof side inner garnish LH as shown in the illustration.
62471A
18.INSTALL ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
73370E
19.CONNECT REAR SEAT OUTER BELT ASSEMBLY LH
73360D
20.CONNECT REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64740C
21.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
|
Install in this Direction |
Engage the guide, clips and claws to install the deck trim side panel assembly LH as shown in the illustration.
Install the 2 screws.
64730B
22.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
64715C
23.INSTALL DECK TRIM SIDE COVER LH
Engage the guide and claw to install the deck trim side cover LH.
64714C
24.INSTALL DECK TRIM SIDE COVER RH
Use the same procedure as for the LH side.
71304C
25.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH
Install the rear seatback hinge sub-assembly LH with the bolt.
71303C
26.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
81330
27.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
64716D
28.INSTALL DECK TRIM REAR COVER
|
Install in this Direction |
Engage the guides and claws to install the deck trim rear cover as shown in the illustration.
62412B
29.INSTALL CENTER PILLAR UPPER GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and clip to install the center pillar upper garnish LH as shown in the illustration.
Install the 2 clips.
62411B
30.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62414A
31.INSTALL CENTER PILLAR LOWER GARNISH LH
|
Install in this Direction |
Engage the guides, clips and claws to install the center pillar lower garnish LH as shown in the illustration.
62413A
32.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73220
33.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73210
34.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73233
35.INSTALL LAP BELT OUTER ANCHOR COVER
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>INSTALLATION
Use the same procedures for the opposite side.
62332A
36.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331A
37.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
67918F
38.INSTALL REAR DOOR SCUFF PLATE INSIDE LH
Engage the guides and claws to install the rear door scuff plate inside LH as shown in the illustration.
| *A | for Gasoline Model | *B | for HV Model |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) | - | - |
67917F
39.INSTALL REAR DOOR SCUFF PLATE INSIDE RH
Use the same procedure as for the LH side.
76974F
40.INSTALL REAR UNDER SIDE COVER LH (for HV Model)
|
Install in this Direction |
Engage the guides and clips to install the rear under side cover LH as shown in the illustration.
Install the clip.
76973F
41.INSTALL REAR UNDER SIDE COVER RH (for HV Model)
|
Install in this Direction |
Engage the guides and clips to install the rear under side cover RH as shown in the illustration.
Install the 2 clips.
62212
42.INSTALL FRONT PILLAR GARNISH LH
62211
43.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62312B
44.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62112
46.INSTALL COWL SIDE TRIM BOARD LH
|
Install in this Direction |
Engage the clip to install the cowl side trim board LH as shown in the illustration.
Install the clip.
62111C
47.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
67914B
48.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the front door scuff plate LH as shown in the illustration.
67913B
49.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
50.INSTALL REAR SEAT ASSEMBLY
64993
51.INSTALL REAR DECK FLOOR BOX (w/ Repair Kit)
Install the rear deck floor box.
64777J
52.INSTALL SPARE WHEEL CUSHION (for Compact Spare Tire)
Install the spare wheel cushion.
64771G
53.INSTALL SPARE WHEEL COVER
Install the spare wheel cover.
58410B
54.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
Install the deck board assembly.
64330D
55.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
|
Install in this Direction |
Engage the guides to install the package tray trim panel assembly as shown in the illustration.
Engage the hooks.