Home › Power Source / Network › M15A-FKS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.07
RM36W0E _57 Power Source / Network _087763 M15A-FKS BATTERY / CHARGING _0419403 CHARGING SYSTEM C

M15A-FKS BATTERY / CHARGING  CHARGING SYSTEM  P058A01  Battery Monitor Module General Electrical Failure  


DESCRIPTION

The battery state sensor assembly detects the voltage, current and temperature of the auxiliary battery. The auxiliary battery state sensor assembly calculates State of Charge (SOC) based on the voltage and current of the auxiliary battery and sends it to the ECM. Based on the signals received, the ECM adjusts the charging voltage of the generator with regulator assembly.

The battery state sensor assembly calculates the battery temperature based on changes in resistance of a built-in thermistor and sends it to the ECM. The ECM reduces the amount of charging current based on this signal in order to protect the auxiliary battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P058A01 Battery Monitor Module General Electrical Failure Any of the following conditions is met with the ignition switch to ON. (1 trip detection logic):
·

Current is 999.939 A or more, or -1000 A or less for 3.2 seconds or more.

·

The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more.

·

A current detection circuit malfunction signal is received.

·

The battery temperature is 105°C or more or -40°C or less for 3.2 seconds or more.

·

A temperature detection circuit malfunction signal is received.

·

Voltage is 15.98 V or more, or 6.0 V or less for 3.2 seconds or more.

·

A voltage detection circuit malfunction signal is received.

·

A writing error occurs in the battery state sensor internal memory (battery identification data).


·

Battery state sensor assembly

·

Auxiliary battery

·

Wire harness or connector


Charge warning light does not come on DTC stored SAE Code: P058A

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status Current value is 999.939 A or more ○ - - - - -
Current value is -1000 A or less - ○ - - - -
Difference between maximum and minimum current value is 0.0305 A or less - - ○ - - -
Current detection circuit malfunction signal is received - - - ○ - -
Battery temperature is 105°C or more - - - - ○ -
Battery temperature is -40°C or less - - - - - ○
Detection Time 3.2 seconds or more 3.2 seconds or more 100 seconds or more - 3.2 seconds or more 3.2 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions
Vehicle Condition
Pattern 7 Pattern 8 Pattern 9 Pattern 10 Pattern 11
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○
Malfunction Status Temperature detection circuit malfunction signal is received ○ - - - -
Voltage value remains at 15.98 V or more - ○ - - -
Voltage value remains at 6.0 V or less - - ○ - -
Voltage detection circuit malfunction signal is received - - - ○ -
writing error occurs in the battery state sensor internal memory (battery identification data) - - - - ○
Detection Time - 3.2 seconds or more 3.2 seconds or more - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

A392149E14
2.448,1.052 2.615,1.302 0.167,0.25 10 false 3 4.031,1.01 4.25,1.26 0.219,0.25 10 false 2 4.854,1.01 5.073,1.26 0.219,0.25 10 false 63 5.125,1.177 5.458,1.427 0.333,0.25 10 false LIN 5.5,3.125 5.833,3.375 0.333,0.25 10 false D51 5.479,3.292 5.896,3.542 0.417,0.25 10 false ECM 2.302,1.667 2.719,1.917 0.417,0.25 10 false A70 2.302,1.833 4.385,2.083 2.083,0.25 10 false Battery State Sensor Assembly 0.729,3.281 2.563,3.531 1.833,0.25 10 false : LIN Communication Line 0.406,1.104 1.313,1.75 0.906,0.646 10 false from Auxiliary Battery 1.469,1.323 2.448,1.615 0.979,0.292 10 false BATT-S NO. 1 2.646,1.156 2.979,1.406 0.333,0.25 10 false +B 3.698,1.177 4.031,1.427 0.333,0.25 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform the inspection for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.

Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>P162B87



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Result
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A70-3 (+B) - Body ground Always 11 to 14 V



Post-procedure1

e.

None.


Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR