Home › Power Source / Network › 1KR-FE (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.07
RM36W0E _57 Power Source / Network _090846 1KR-FE BATTERY / CHARGING _0430815 CHARGING SYSTEM C

1KR-FE BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Charge warning light:
Does not come on
DTC stored SAE Code: P161A

WIRING DIAGRAM

A340530E93
1.51,3.167 5.177,3.365 3.667,0.198 10 false : LIN Communication Line 1.802,2.271 2.26,2.469 0.458,0.198 10 false D53 1.792,2.427 3.135,2.792 1.344,0.365 10 false Generator Assembly 4.844,2.521 5.302,2.719 0.458,0.198 10 false D50 4.833,2.688 6.802,3.177 1.969,0.49 10 false ECM 3.104,1.542 3.438,1.823 0.333,0.281 10 false 2 4.635,1.542 4.969,1.823 0.333,0.281 10 false 76 2.802,1.74 3.26,1.938 0.458,0.198 10 false LIN 4.896,1.719 5.354,1.917 0.458,0.198 10 false LIN 0.167,0.177 4.938,0.417 4.771,0.24 12 false w/o Stop and Start System:

A427236E25
0.438,0.698 1.354,1.354 0.917,0.656 10 false from Auxiliary Battery 1.594,0.854 2.51,1.094 0.917,0.24 10 false BATT-S NO. 1 2.5,0.625 2.635,0.833 0.135,0.208 10 false 3 2.677,0.708 2.927,0.938 0.25,0.229 10 false +B 3.729,0.719 3.979,0.948 0.25,0.229 10 false LIN 4.063,0.573 4.313,0.802 0.25,0.229 10 false 2 2.417,1.167 2.802,1.427 0.385,0.26 10 false A70 2.427,1.323 4.542,1.552 2.115,0.229 10 false Battery State Sensor Assembly 2.646,2.667 3.031,2.927 0.385,0.26 10 false D53 2.677,2.833 4.969,3.083 2.292,0.25 10 false Generator Assembly 1.083,3.177 3.198,3.406 2.115,0.229 10 false : LIN Communication Line 5.854,0.719 6.146,0.958 0.292,0.24 10 false LIN 5.583,0.542 5.833,0.771 0.25,0.229 10 false 76 6.063,1.813 6.354,2.052 0.292,0.24 10 false D50 6.073,1.979 6.583,2.208 0.51,0.229 10 false ECM 3.719,2.167 4.229,2.396 0.51,0.229 10 false LIN 4.052,2.052 4.302,2.281 0.25,0.229 10 false 2 0.198,0.083 2.448,0.354 2.25,0.271 12 false w/ Stop and Start System:

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK CHARGING SYSTEM

B

4.CHECK CHARGING SYSTEM
2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D50 ECM connector.


b.

Disconnect the D53 generator assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D53-2 (LIN) - D50-76 (LIN) Always Below 1 Ω
D53-2 (LIN) or D50-76 (LIN) - Body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CHARGING SYSTEM

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR WITH REGULATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR WITH REGULATOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D50 ECM connector.


b.

Disconnect the D53 generator with regulator assembly connector.


c.

Disconnect the A70 battery state sensor assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A70-2 (LIN) or D53-2 (LIN) - D50-76 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A70-2 (LIN), D53-2 (LIN) or D50-76 (LIN) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check for DTCs, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

h.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Allow the engine to idle for approximately 17 minutes or more.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only DTC P161A87 is output. A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C