Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM (for TMC Made LH Side) › 2020.07–2020.09
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0431055 FRONT LOWER SUSPENSION ARM(for TMC Made LH Side) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for TMC Made LH Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front lower No. 1 suspension arm sub-assembly LH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 51451A 2.REMOVE CENTER ENGINE UNDER COVER

Hide 48069 3.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C428572

Remove the clip and nut from the front lower No. 1 suspension arm sub-assembly LH.


b.
C428573E01
0.438,1.635 0.813,0.906 true 0.302,1.698 0.656,1.896 0.354,0.198 10 true SST

Install SST to the front lower No. 1 suspension arm sub-assembly LH as shown in the illustration.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the front lower No. 1 suspension arm sub-assembly LH and SST are aligned.



c.

Using SST, separate the front lower No. 1 suspension arm sub-assembly LH from the steering knuckle.

C428574C01
1.823,0.302 2.365,0.177 true 2.083,0.917 2.333,0.917 true 5.229,1.083 5.417,0.833 true 5.125,1.052 5.438,1.208 0.313,0.156 10 false *a 3.25,0.719 3.563,0.875 0.313,0.156 10 false *b 2.448,0.094 2.76,0.25 0.313,0.156 10 false *c 5.438,1.25 5.75,1.406 0.313,0.156 10 false *d 2.854,1.5 3.167,1.656 0.313,0.156 10 false *e 2.427,0.833 2.833,1 0.406,0.167 10 false SST 3.271,0.427 3.583,0.583 0.313,0.156 10 false *b 6.333,0.375 6.677,0.583 0.344,0.208 10 false A 6.333,0.625 6.677,0.833 0.344,0.208 10 false B
*a Center Nut *b Molybdenum grease application area
*c String *d Place wrench here
*e Turn - -


SST
09960-20010  (09961-02010, 09961-02060)

CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.

·

Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.

·

Do not damage the drive shaft outboard joint boot.




Hide 48069 4.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C434412

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.