The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
| *a | Cord |
When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.
2.DRAIN FUEL
3.REMOVE WHEEL ASSEMBLY
65638
4.SEPARATE REAR WHEEL HOUSE LINER LH
Remove the 2 screws.
Remove the 5 clips.
Remove the grommet and separate the rear fender liner.
77020A
5.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
77310A
6.REMOVE FUEL TANK CAP ASSEMBLY
51447D
7.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMC Made)
51447D
8.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMMF Made)
17410
9.REMOVE FRONT EXHAUST PIPE ASSEMBLY
77606
10.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Remove the 3 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.
77027B
11.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Disconnect the No. 1 fuel emission tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
77209F
12.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
13.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY
Remove the bolt.
Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.
77100U
14.REMOVE FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Support the fuel tank assembly using an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 4 bolts.
Lower the engine lifter to remove the fuel tank assembly.
Be careful not to drop the fuel tank assembly.
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
77209F
15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disengage the clamp to remove the fuel tank main tube sub-assembly from the fuel tank assembly.
77027B
16.REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Disengage the clamp to remove the No. 1 fuel emission tube sub-assembly from the fuel tank assembly.
77217A
17.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT
Disengage the 2 claws to remove the No. 2 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77216A
18.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT
Disengage the 3 clamps to remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77218A
19.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT
Disengage the 3 clamps to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77277R
20.REMOVE FUEL TANK FILLER PIPE PROTECTOR
Disengage the 4 claws.
Disengage the 4 clamps to remove the fuel tank filler pipe protector from the fuel tank filler pipe sub-assembly.