Home › Engine / Hybrid System › 1KR-FE (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _090964 1KR-FE EMISSION CONTROL _0431148 EMISSION CONTROL SYSTEM G

1KR-FE EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL CUT OPERATION

a.

Start the engine.


b.

Warm up the engine.


c.

Increase the engine speed to approximately 3000 rpm.


d.
A468048C01
0.958,0.708 1.323,0.708 true 1.75,1.104 2.115,1.104 true 2.135,1 2.344,1.198 0.208,0.198 10 true *1 0.771,0.604 0.958,0.792 0.188,0.188 10 true *a
*1 Fuel Injector Assembly
*a Sound Scope


Use a sound scope to check for fuel injector assembly operating sounds.


e.

When the accelerator pedal is fully released, check that fuel injector assembly operating sounds stop momentarily and then resume.

Standard:
Item Specified Condition
Fuel injection restart engine speed 1040 rpm


If the result is not as specified, check the fuel injector assemblies, wire harness and ECM.


Hide 2.VISUALLY CHECK HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil level dipstick, oil filler cap sub-assembly, ventilation hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in any part of the air induction system between the throttle body with motor assembly and cylinder head sub-assembly will cause engine failure or engine malfunctions.



If any defects are found, replace parts as necessary.


Hide 3.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.
A468049

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Evap Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

f.

Check that vacuum occurs at the purge valve (purge VSV) port.


g.

If vacuum does not occur, check the following items:

·

Purge valve (purge VSV)

·

Clogs in the No. 2 fuel vapor feed hose that connects the intake manifold and purge valve (purge VSV)



h.

Exit Active Test mode and connect the No. 1 fuel vapor feed hose and slide the clip to secure it.


i.

Enter the following menus: Powertrain / Engine / Data List / EVAP Purge VSV.

Powertrain > Engine > Data List
Tester Display
EVAP Purge VSV
50003 372 271

j.

Warm up the engine and drive the vehicle.


k.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.


Hide 25620 4.INSPECT EGR SYSTEM

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Active test / Control the EGR Step Position.

Powertrain > Engine > Active Test
Tester Display
Control the EGR Step Position
50004 372 25

f.

Check the engine speed when the EGR valve assembly is operated by the GTS.


g.

Perform the Active Test by referring to the table below.

HINT:

Test is possible with vehicle stopped and engine idling.


OK:
Condition Specified Condition
Open the EGR valve assembly gradually
(Increase number of steps)
As the valve opens, engine changes from steady idling to rough idling
Close the EGR valve assembly gradually
(Decrease number of steps)
As the valve closes, engine changes from rough idling to steady idling