Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431329 REAR CRANKSHAFT OIL SEAL A

1KR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A322229C01
0,0 0,0 false
V100144

Apply engine oil


Apply engine oil to the lip of a new rear engine oil seal.


c.
A322230N01
1.26,1.01 1.802,1.635 1.802,1.635 1.729,1.115 true 2.813,0.906 2.917,0.719 2.917,0.719 2.354,0.823 false 1.667,1.667 2.125,1.865 0.458,0.198 10 true SST 2.969,0.625 3.427,0.823 0.458,0.198 10 false SST 3.198,1.354 3.354,1.552 0.156,0.198 10 false - 3.198,1.75 3.354,1.948 0.156,0.198 10 false +

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the rear engine oil seal edge.

Standard Depth:

-0.5 to 1.0 mm (-0.0197 to 0.0394 in.)


SST
09223-15020  
09950-70010  (09951-07200)

NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 13405 2.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Clean the 6 bolts and 6 bolt holes.


c.
A057108C38
2.521,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.563,0.156 2.74,0.333 0.177,0.177 10 *a
*a Adhesive 1324


Apply adhesive to 2 or 3 threads at the tip of each of the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.
A322227N01
1.26,0.365 1.417,0.563 0.156,0.198 10 true 1 1.906,1.625 2.063,1.823 0.156,0.198 10 true 2 0.896,0.958 1.052,1.156 0.156,0.198 10 true 3 2.281,1.042 2.438,1.24 0.156,0.198 10 true 4 1.26,1.594 1.417,1.792 0.156,0.198 10 true 5 1.958,0.385 2.115,0.583 0.156,0.198 10 true 6

Install the flywheel sub-assembly to the crankshaft with the 6 bolts in the sequence shown in the illustration.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31250 3.INSTALL CLUTCH DISC ASSEMBLY