Home › Drivetrain › CLUTCH › CLUTCH UNIT (for C551) › from 2020.07
RM36W0E _52 Drivetrain _089426 CLUTCH _0430798 CLUTCH UNIT(for C551) A

CLUTCH  CLUTCH UNIT(for C551)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
F100378C02
2.75,0.958 2.083,0.771 true 2.063,2.323 1.656,2.5 false 0.865,3.458 1.094,3.708 0.229,0.25 10 false *a 2.813,0.875 3.146,1.073 0.333,0.198 10 false SST 2.094,2.24 2.271,2.438 0.177,0.198 10 false *1
*1 Clutch Disc Assembly
*a Flywheel side


Insert SST into the clutch disc assembly, and then insert them both into the flywheel sub-assembly.

SST
09301-00131  

NOTICE:

Insert clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C437879C01
1.74,1.615 2.365,1.865 2.365,1.865 1.802,1.74 true 0.802,0.667 0.396,0.438 true 2.438,1.781 2.729,2 0.292,0.219 10 true *a 2.219,0.24 2.917,0.458 0.698,0.219 10 true 1 (*b), 4 0.115,0.344 0.448,0.531 0.333,0.188 10 false SST 0.406,0.792 0.563,0.99 0.156,0.198 10 false 3 0.917,1.885 1.073,2.083 0.156,0.198 10 true 2 0.354,1.479 0.51,1.677 0.156,0.198 10 true 6 2.313,1.323 2.469,1.521 0.156,0.198 10 true 5 0.906,0.26 1.063,0.458 0.156,0.198 10 true 7
*a Matchmark
*b Temporarily


Align the match mark on the clutch cover assembly with that on the flywheel sub-assembly.


b.

Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00131  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the disc is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C062961

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)



b.
D029849E04
1.74,0.802 2.313,1.563 false 2.344,1.469 2.708,1.677 0.365,0.208 10 false SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
F100377E01
0.186,0.127 0.537,0.346 0.350,0.218 10 SST 0.547,0.256 1.484,0.342 false 0.547,0.256 1.338,1.279 false

Using SST and a hammer, tap in a new clutch release fork shaft oil seal until its surface is flush with the transaxle case.

SST
09950-60010  (09951-00290)
09950-70010  (09951-07150)


Hide 31204 5.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C118345C01
0,0 0,0 false
V100135

Clutch release hub grease


Apply release hub grease to the contact surface between the clutch release bearing assembly and the clutch release fork, the rotating and sliding parts of the clutch release fork shaft and the spline coupling part.

Grease:

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


NOTICE:

Apply grease uniformly to the rotating and sliding parts of the clutch release fork shaft and the spline coupling part. Remove any grease extending beyond the clutch release fork shaft joining part.



b.

Install the clutch release fork sub-assembly to the transaxle case together with the clutch release fork.


c.
F100370

Using a screwdriver and hammer, install a new E-ring.


Hide 31230 6.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Engage the release bearing hub clip and install the clutch release bearing assembly to the clutch release fork.


b.
C242389C01
0,0 0,0 false
V100135

Clutch spline grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31121 7.INSTALL NO. 1 CLUTCH HOUSING COVER

a.

Install the No. 1 clutch housing cover to the manual transaxle assembly.


Hide 30300 8.INSTALL MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge)

Hide 30300 9.INSTALL MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge)