Home › Engine / Hybrid System › 1KR-FE (COOLING) › COOLING FAN SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091037 1KR-FE COOLING _0431355 COOLING FAN SYSTEM J

1KR-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

To control the cooling fans, the ECM turns on or off the cooling fan relays based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.

The ECM turns on or off the fan relays to switch the cooling fan motor circuit between the series circuit and parallel circuit, controlling the cooling fan motor speed in 2 steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FAN RELAY (FAN WITH MOTOR ASSEMBLY POWER SOURCE)
a.
A450957C02
0.063,0.052 0.375,0.208 0.313,0.156 10 false *1 0.344,2.26 0.656,2.417 0.313,0.156 10 false *2
*1 Engine Room R/B Assembly
*2 FAN No. 1 Relay


Remove the FAN No. 1 relay from the engine room R/B assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FAN No. 1 relay terminal 3 - Body ground Always 11 to 14 V



c.

Reinstall the FAN No. 1 relay.


Result:
Proceed to
OK
NG



OK

2.CHECK EFI-MAIN NO. 1 RELAY (FAN WITH MOTOR ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.CHECK EFI-MAIN NO. 1 RELAY (FAN WITH MOTOR ASSEMBLY POWER SOURCE)
a.
A459385C03
0.031,0.042 0.344,0.198 0.313,0.156 10 false *1 1.531,2.135 1.781,2.354 0.25,0.219 10 false *2
*1 Engine Room R/B Assembly
*2 EFI-MAIN No. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the engine room R/B assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI-MAIN NO. 1 relay terminal 3 - Body ground ON 11 to 14 V
EFI-MAIN NO. 1 relay terminal 2 - Body ground ON 11 to 14 V



c.

Reinstall the EFI-MAIN NO. 1 relay


Result:
Proceed to
OK
NG



OK

3.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT FAN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

4.INSPECT FAN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

5.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPLACE FAN NO. 2 RELAY

5.INSPECT EFI-MAIN NO. 1 RELAY
a.

Inspect the EFI-MAIN NO. 1 relay.

Click hereEngine / Hybrid System>1KR-FE (COOLING)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 1 RELAY - EFI-MAIN NO. 1 RELAY)

NG

REPLACE EFI-MAIN NO. 1 RELAY

6.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 1 RELAY - EFI-MAIN NO. 1 RELAY)
a.

Remove the FAN No. 1 relay and EFI-MAIN NO. 1 relay from the engine room R/B assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FAN No. 1 relay terminal 1 - EFI-MAIN NO. 1 relay terminal 5 Always Below 1 Ω
FAN No. 1 relay terminal 1 or EFI-MAIN NO. 1 relay terminal 5 - Body ground Always 10 kΩ or higher



c.

Reinstall the FAN No. 1 relay and EFI-MAIN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 2 RELAY - EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 2 RELAY - EFI-MAIN NO. 1 RELAY)
a.

Remove the FAN No. 2 relay and EFI-MAIN NO. 1 relay from the engine room R/B assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FAN No. 2 relay terminal 2 - EFI-MAIN NO. 1 relay terminal 5 Always Below 1 Ω
FAN No. 2 relay terminal 2 or EFI-MAIN NO. 1 relay terminal 5 - Body ground Always 10 kΩ or higher



c.

Reinstall the FAN No. 2 relay and EFI-MAIN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

8.INSPECT COOLING FAN RESISTOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

8.INSPECT COOLING FAN RESISTOR

Inspect the cooling fan resistor.

Click hereEngine / Hybrid System>1KR-FE (COOLING)>COOLING FAN RESISTOR>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG



OK

9.CHECK FAN NO. 2 RELAY - BODY GROUND

NG

REPLACE COOLING FAN RESISTOR

9.CHECK FAN NO. 2 RELAY - BODY GROUND
a.

Remove the FAN No. 2 relay and EFI-MAIN NO. 1 relay from the engine room R/B assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FAN No. 2 relay terminal 5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN RESISTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

10.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN RESISTOR - BODY GROUND)
a.

Disconnect the cooling fan resistor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 (Cooling Fan Resistor) - Body ground Always Below 1 Ω



c.

Reconnect the cooling fan resistor connector.


Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 2 RELAY - COOLING FAN RESISTOR)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

11.CHECK WIRE HARNESS AND CONNECTORS (FAN NO. 2 RELAY - COOLING FAN RESISTOR)
a.

Disconnect the cooling fan resistor connector.


b.

Remove the FAN No. 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-2 (Cooling Fan Resistor) - FAN No. 2 relay terminal 4 Always Below 1 Ω
A47-2 (Cooling Fan Resistor) or FAN No. 2 relay terminal 4 - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN No. 2 relay.


e.

Reconnect the cooling fan resistor connector.


Result:
Proceed to
OK
NG



OK

12.CHECK COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

12.CHECK COOLING FAN MOTOR

Result:
Proceed to
OK
NG



OK

13.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN MOTOR - FAN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

13.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN MOTOR - FAN NO. 1 RELAY)
a.

Disconnect the cooling fan motor connector.


b.

Remove the FAN No. 1 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-2 (Cooling Fan Motor) - FAN No. 1 relay terminal 5 Always Below 1 Ω
A46-2 (Cooling Fan Motor) or FAN No. 1 relay terminal 5 - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN No. 1 relay.


e.

Reconnect the cooling fan motor connector.


Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN MOTOR - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

14.CHECK WIRE HARNESS AND CONNECTORS (COOLING FAN MOTOR - FAN NO. 2 RELAY)
a.

Disconnect the cooling fan motor connector.


b.

Remove the FAN No. 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-1 (Cooling Fan Motor) - FAN No. 2 relay terminal 3 Always Below 1 Ω
A46-1 (Cooling Fan Motor) or FAN No. 2 relay terminal 3 - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN No. 2 relay.


e.

Reconnect the cooling fan motor connector.


Result:
Proceed to
OK
NG



OK

15.CHECK WIRE HARNESS AND CONNECTORS (ECM - ENGINE ROOM R/B ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

15.CHECK WIRE HARNESS AND CONNECTORS (ECM - ENGINE ROOM R/B ASSEMBLY)
a.

Remove the FAN No. 1 relay, FAN No. 2 relay and EFI-MAIN NO. 1 relay from the engine room R/B assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-22 (FANL) - FAN No. 1 relay terminal 2 Always Below 1 Ω
A55-23 (FANH) - FAN No. 2 relay terminal 1 Always Below 1 Ω
A55-9 (MREL) - EFI-MAIN NO. 1 relay terminal 1 Always Below 1 Ω
A55-22 (FANL) or FAN No. 1 relay terminal 2 - Body ground Always 10 kΩ or higher
A55-23 (FANH) or FAN No. 2 relay terminal 1 - Body ground Always 10 kΩ or higher
A55-9 (MREL) or EFI-MAIN NO. 1 relay terminal 1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the FAN No. 1 relay, FAN No. 2 relay and EFI-MAIN NO. 1 relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR