Home › Engine / Hybrid System › 1KR-FE (COOLING) › WATER PUMP › from 2020.07
RM36W0E _51 Engine / Hybrid System _091037 1KR-FE COOLING _0431357 WATER PUMP G

1KR-FE COOLING  WATER PUMP  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FOR COOLANT LEAK

HINT:
·

The sliding surface inside the engine water pump assembly is lubricated by engine coolant. As some engine coolant is discharged during normal operation, coolant residue (solids) may be found on the drain plug or the bottom of the engine water pump assembly. Engine coolant may leak if foreign matter enters the engine water pump assembly, however the sealing performance will recover when the foreign matter is pushed out or breaks into fine pieces.

·

Before performing this inspection, check that there is no engine coolant leaking from any parts other than the engine water pump assembly. If there are leaks, inspect those areas.

·

Perform this inspection when the engine is cold.



a.

Visually check the engine water pump assembly.

i.

Check that engine coolant is not dripping from the engine water pump assembly.

HINT:
·

If engine coolant is dripping, replace the engine water pump assembly.

·

If engine coolant is not dripping, perform the following check.





b.

Inspect the area around the engine water pump assembly.

HINT:

Check for deposits around the drain plug of the engine water pump assembly.


i.
A323953C03
0.417,2.281 0.656,2.281 false 1.198,0.625 1.021,0.438 false 1.948,2.875 1.563,2.51 false 0.219,2.198 0.448,2.365 0.229,0.167 10 false *a 1.99,2.844 2.188,3 0.198,0.156 10 false *2 0.813,0.354 1.042,0.521 0.229,0.167 10 false *1
*1 Water Pump Pulley
*2 Drain Plug
*a Water Pump Pulley Hole


Rotate the crankshaft pulley and align the water pump pulley hole with the drain plug.

HINT:
·

The drain plug is at the bottom of the engine water pump assembly.

·

Use a mirror to check that the water pump pulley hole and drain plug are aligned.




ii.
A323954C03
2.24,1.125 2.583,0.781 true 1.938,0.854 2.281,0.5 true 2.313,0.385 2.51,0.552 0.198,0.167 10 true *a 2.625,0.677 2.823,0.844 0.198,0.167 10 true *b
*a Thin Paper Towel
*b Hexagon Wrench


Wrap a thin paper towel around an L-shaped tool such as a hexagon wrench, and insert it into the water pump pulley hole.

HINT:
·

Use a 3 mm (0.118 in.) hexagon wrench.

·

The diameter of the water pump pulley hole is 6 mm (0.236 in.).

·

The distance from the water pump pulley hole to the drain plug is 15 mm (0.591 in.).




iii.
A323955C02
0.359,2.017 0.564,2.186 0.205,0.170 10 *a 1.343,2.673 1.547,2.843 0.205,0.170 10 *b 0.577,2.114 0.821,2.114 false 1.075,2.766 1.318,2.766 false
*a Thin Paper Towel
*b Hexagon Wrench


Move the hexagon wrench as shown in the illustration, and press the thin paper towel against the engine coolant (solid matter) adhering to the drain plug or the edge of the drain plug, and check the condition of the thin paper towel.

HINT:
·

If the thin paper towel is wet, replace the engine water pump assembly.

·

If the thin paper towel is dry, clean the area around the engine water pump assembly.





Hide 16100 2.INSPECT ENGINE WATER PUMP ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereGeneral>MAINTENANCE>1KR-FE DRIVE BELT>REMOVAL


b.
A323956

Turn the water pump pulley and check that the engine water pump assembly bearing moves smoothly and quietly.

If necessary, replace the engine water pump assembly.


c.

Install the fan and generator V belt.

Click hereGeneral>MAINTENANCE>1KR-FE DRIVE BELT>INSTALLATION