Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00D214  Restraint System Malfunction Indicator 1 Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B00D214 Restraint System Malfunction Indicator 1 Circuit Short to Ground or Open
·

The airbag sensor assembly detects a short to ground in the restraint system malfunction indicator 1 circuit when the airbag sensor assembly sends a passenger airbag indicator OFF signal to the passenger airbag ON indicator

·

The airbag sensor assembly detects an open in the restraint system malfunction indicator 1 circuit when the airbag sensor assembly sends a passenger airbag indicator OFF signal to the passenger airbag ON indicator

·

Telltale light assembly malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Telltale light assembly

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

C414933E04
5.5,1.083 6.115,1.281 0.615,0.198 10 false PAON 1.5,1.083 2,1.271 0.5,0.188 10 false PAON 0.615,0.833 1,1.083 0.385,0.25 10 false IGR 5.219,1.083 5.833,1.281 0.615,0.198 10 false 35 2.031,1.083 2.583,1.281 0.552,0.198 10 false 3 0.375,1.896 0.99,2.094 0.615,0.198 10 false H8 5.333,1.906 5.948,2.104 0.615,0.198 10 false H14 5.323,2.073 7.01,2.417 1.688,0.344 10 false Airbag Sensor Assembly 0.385,2.094 2.073,2.531 1.688,0.438 10 false Telltale Light Assembly 1.667,0.688 2,0.917 0.333,0.229 10 false IG+ 2.031,0.552 2.583,0.75 0.552,0.198 10 false 5 3.083,0.688 4.917,1.083 1.833,0.396 10 false from ECU-IGR NO. 2 fuse 0.802,1.417 1.917,1.813 1.115,0.396 10 false Passenger Airbag ON Indicator

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>OPERATION CHECK



Result:
Result Proceed to
Passenger airbag ON indicator is always on A
Passenger airbag ON indicator is always off B



A

2.CHECK CONNECTION OF CONNECTORS

B

6.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422880C01
0.75,0.427 1.115,0.667 0.365,0.24 0.771,3.729 1.135,3.969 0.365,0.24 1.635,2.99 1.635,2.74 false 2.24,1.802 2.031,1.302 true 1.729,3.917 2.188,4.292 true 0.417,2.583 0.667,2.833 0.25,0.25 10 false *1 2.75,2.583 3.135,2.906 0.385,0.323 10 false *2 0.656,0.167 1.021,0.417 0.365,0.25 10 false *b 0.646,3.417 0.896,3.667 0.25,0.25 10 false *a 1.573,3.021 1.969,3.25 0.396,0.229 10 false *3 2.354,2.583 2.583,2.833 0.229,0.25 10 false A 1.99,2.583 2.167,2.823 0.177,0.24 10 false B 1.135,2.583 1.333,2.833 0.198,0.25 10 false C 0.771,2.583 0.917,2.833 0.146,0.25 10 false D 0.802,0.458 1.135,0.656 0.333,0.198 10 false H14 2.292,1.729 2.823,1.958 0.531,0.229 10 false PAON 0.854,3.76 1.115,3.958 0.26,0.198 10 false H8 2.229,4.219 2.708,4.49 0.479,0.271 10 false PAON
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-3 (PAON) or H14-35 (PAON) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

5.CHECK TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELLTALE LIGHT ASSEMBLY

Pre-procedure1

a.
C431635C02
1.479,1.604 1.479,1.156 false 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2 1.417,1.625 1.781,1.885 0.365,0.26 10 false *3
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Connect the connector to the telltale light assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


Procedure1

d.

Check the passenger airbag ON indicator operation.

OK:

The passenger airbag ON indicator does not come on.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

NG

6.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

7.CHECK CONNECTORS

Pre-procedure1

a.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

8.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (OPEN)
a.
C422880C01
0.75,0.427 1.115,0.667 0.365,0.24 0.771,3.729 1.135,3.969 0.365,0.24 1.635,2.99 1.635,2.74 false 2.24,1.802 2.031,1.302 true 1.729,3.917 2.188,4.292 true 0.417,2.583 0.667,2.833 0.25,0.25 10 false *1 2.75,2.583 3.135,2.906 0.385,0.323 10 false *2 0.656,0.167 1.021,0.417 0.365,0.25 10 false *b 0.646,3.417 0.896,3.667 0.25,0.25 10 false *a 1.573,3.021 1.969,3.25 0.396,0.229 10 false *3 2.354,2.583 2.583,2.833 0.229,0.25 10 false A 1.99,2.583 2.167,2.823 0.177,0.24 10 false B 1.135,2.583 1.333,2.833 0.198,0.25 10 false C 0.771,2.583 0.917,2.833 0.146,0.25 10 false D 0.802,0.458 1.135,0.656 0.333,0.198 10 false H14 2.292,1.729 2.823,1.958 0.531,0.229 10 false PAON 0.854,3.76 1.115,3.958 0.26,0.198 10 false H8 2.229,4.219 2.708,4.49 0.479,0.271 10 false PAON
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-3 (PAON) - H14-35 (PAON) Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

9.CHECK WIRE HARNESS (SOURCE VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK WIRE HARNESS (SOURCE VOLTAGE)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H8-5 (IG+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

10.CHECK TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TELLTALE LIGHT ASSEMBLY

Pre-procedure1

a.
C422881C01
0.604,1.948 1.021,2.198 0.417,0.25 2.167,2.885 2.552,2.615 true 1.5,1.042 1.5,0.625 false 0.406,0.458 0.667,0.75 0.26,0.292 10 false *1 2.802,0.458 3.167,0.75 0.365,0.292 10 false *2 1.448,1.052 1.75,1.333 0.302,0.281 10 false *3 0.469,1.552 0.917,2.146 0.448,0.594 10 false *a 0.698,1.99 1.031,2.271 0.333,0.281 10 false H14 2.594,2.531 3.083,2.917 0.49,0.385 10 false PAON 2.354,0.469 2.729,0.781 0.375,0.313 10 false A 1.99,0.469 2.365,0.781 0.375,0.313 10 false B 0.927,0.469 1.302,0.781 0.375,0.313 10 false C 0.771,0.469 1.146,0.781 0.375,0.313 10 false D
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the telltale light assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


Procedure1

d.

Check the passenger airbag ON indicator according to the conditions in the table below.

OK:
Terminal Connection Switch Condition Specified Condition
H14-35 (PAON) - Body ground Ignition switch ON Passenger airbag ON indicator comes on


Result:
Proceed to
OK
NG



Post-procedure1

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

NG