PRECAUTION FOR OPERATION CHECK
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Be sure to correctly follow the removal and installation procedures for the SRS parts.
If there is any damage or deformation of airbag installation components or the areas they are installed to, do not attempt to repair them. Replace the damaged components with new ones.
CHECK SRS WARNING LIGHT
Primary check
Turn the ignition switch to ON and check that the SRS warning light turns on.
Turn the ignition switch off. Wait for at least 2 seconds, then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.
If the SRS warning light remains on for approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a malfunction in the SRS airbag system.
If the SRS warning light occasionally turns on approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a short to +B, short to ground or an open in the SRS warning light circuit.
If the SRS warning light illuminates after turning the ignition switch off or to ACC, there may be a malfunction in the power source circuit or combination meter assembly.
The SRS warning light turns off, and then turns on. This blinking pattern indicates a power source voltage drop. The SRS warning light turns off 6 to 10 seconds after the power source voltage returns to normal.
FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)
Initial check
Turn the ignition switch to ON.
The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then turns off for approximately 2 seconds.
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.
| Airbag Cut Off Switch Cylinder Sub-assembly Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
|
*1: The ON indicator illuminates for approximately 60 seconds and then turns off. |
|||
| ON | ON*1 | OFF | OFF |
| OFF | OFF | ON | OFF |
| Switch failure | OFF | ON | ON |
If the SRS warning light is not illuminated and the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status, no related DTCs will be stored. Proceed to the Trouble in Passenger Airbag ON/OFF Indicator troubleshooting procedure.
CHECK PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)
Turn the ignition switch to ON.
Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then turns off for approximately 2 seconds.
Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the ignition switch is turned to ON and approximately 6 seconds elapse.
INSPECT AIRBAG COMPONENTS
Inspect the SRS parts in table below.
| Component to Inspect | Procedure |
|---|---|
| Horn button assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the horn button assembly installed to the vehicle.
If any defects are found, replace the horn button assembly with a new one. |
| Instrument panel passenger without door airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the instrument panel passenger without door airbag assembly installed to the vehicle.
If any defects are found, replace the instrument panel safety pad assembly with a new one. |
| Curtain shield airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the curtain shield airbag assemblies installed to the vehicle.
If any defects are found, replace each pillar garnish or the roof headlining assembly with a new one. |
| Front seat airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the front seat airbag assemblies installed to the vehicle.
If any defects are found, replace the separate type front seatback cover with pad with a new one. |
| Front seat center airbag assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the front seat center airbag assemblies installed to the vehicle.
If any defects are found, replace the separate type front seatback cover with pad with a new one. |
| Front seat outer belt assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the front seat outer belt assemblies installed to the vehicle.
If any defects are found, replace the front seat outer belt assembly with a new one. |
| Rear seat outer belt assembly | 1.
Perform a diagnostic system check. 2.
Visually check for defects with the rear seat outer belt assemblies installed to the vehicle.
If any defects are found, replace the rear seat outer belt assembly with a new one. |
| Airbag sensor assembly | 1.
Perform a diagnostic system check. |
| Front airbag sensor | |
| Side airbag pressure sensor | |
| No. 1 side airbag sensor | |
| No. 2 side airbag sensor | |
| Harness and connector |