Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

This circuit detects the airbag cut off switch cylinder sub-assembly status.

The passenger airbag ON/OFF indicator comes on to inform the driver of the instrument panel passenger without door airbag assembly status (activated or deactivated).

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>OPERATION CHECK


WIRING DIAGRAM

B512690E13
4.854,2.979 5.479,3.177 0.625,0.198 10 false H14 4.844,3.146 6.583,3.542 1.74,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.177,3 0.635,0.177 10 false H15 0.542,2.99 3.552,3.396 3.01,0.406 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off.


HINT:
·

If the SRS warning light is on when this malfunction occurs, a DTC is stored. Troubleshoot for the stored DTC.

·

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTORS

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG




OK

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

OK

5.CHECK WIRE HARNESS (SHORT)

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

5.CHECK WIRE HARNESS (SHORT)
a.
C422878C01
0.729,2.167 1.083,2.417 0.354,0.25 1.24,2.802 1.583,2.385 true 2.188,2.802 1.854,2.385 true 1.635,1.104 1.635,0.771 false 0.417,0.615 0.667,0.833 0.25,0.219 10 false *1 2.75,0.615 3.083,0.917 0.333,0.302 10 false *2 1.583,1.146 1.896,1.385 0.313,0.24 10 false *3 0.625,1.646 1.042,1.896 0.417,0.25 10 false *a 1.073,2.833 1.583,3.083 0.51,0.25 10 false PMC- 2.104,2.833 2.667,3.083 0.563,0.25 10 false PMC+ 0.792,2.208 1.167,2.417 0.375,0.208 10 false H15 2.354,0.615 2.583,0.833 0.229,0.219 10 false A 1.979,0.615 2.167,0.833 0.188,0.219 10 false B 1.146,0.615 1.333,0.833 0.188,0.219 10 false C 0.771,0.615 0.917,0.833 0.146,0.219 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H15-2 (PMC+) - H15-1 (PMC-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422878C01
0.729,2.167 1.083,2.417 0.354,0.25 1.24,2.802 1.583,2.385 true 2.188,2.802 1.854,2.385 true 1.635,1.104 1.635,0.771 false 0.417,0.615 0.667,0.833 0.25,0.219 10 false *1 2.75,0.615 3.083,0.917 0.333,0.302 10 false *2 1.583,1.146 1.896,1.385 0.313,0.24 10 false *3 0.625,1.646 1.042,1.896 0.417,0.25 10 false *a 1.073,2.833 1.583,3.083 0.51,0.25 10 false PMC- 2.104,2.833 2.667,3.083 0.563,0.25 10 false PMC+ 0.792,2.208 1.167,2.417 0.375,0.208 10 false H15 2.354,0.615 2.583,0.833 0.229,0.219 10 false A 1.979,0.615 2.167,0.833 0.188,0.219 10 false B 1.146,0.615 1.333,0.833 0.188,0.219 10 false C 0.771,0.615 0.917,0.833 0.146,0.219 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H15-2 (PMC+) - Body ground Always 1 MΩ or higher
H15-1 (PMC-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK WIRE HARNESS (SHORT TO B+)
a.
C422878C01
0.729,2.167 1.083,2.417 0.354,0.25 1.24,2.802 1.583,2.385 true 2.188,2.802 1.854,2.385 true 1.635,1.104 1.635,0.771 false 0.417,0.615 0.667,0.833 0.25,0.219 10 false *1 2.75,0.615 3.083,0.917 0.333,0.302 10 false *2 1.583,1.146 1.896,1.385 0.313,0.24 10 false *3 0.625,1.646 1.042,1.896 0.417,0.25 10 false *a 1.073,2.833 1.583,3.083 0.51,0.25 10 false PMC- 2.104,2.833 2.667,3.083 0.563,0.25 10 false PMC+ 0.792,2.208 1.167,2.417 0.375,0.208 10 false H15 2.354,0.615 2.583,0.833 0.229,0.219 10 false A 1.979,0.615 2.167,0.833 0.188,0.219 10 false B 1.146,0.615 1.333,0.833 0.188,0.219 10 false C 0.771,0.615 0.917,0.833 0.146,0.219 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H15-2 (PMC+) - Body ground Ignition switch ON Below 1 V
H15-1 (PMC-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

8.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (OPEN)
a.
C422877C01
0.781,0.854 1.146,1.073 0.365,0.219 0.76,3.74 1.125,3.958 0.365,0.219 1.833,1.771 1.833,1.688 false 1.25,1.667 1.802,1.094 true 2.417,1.667 1.896,1.094 true 1.281,4.26 1.521,3.927 true 1.948,4.26 1.74,3.927 true 1.625,2.99 1.625,2.74 true 0.375,2.573 0.667,2.917 0.292,0.344 10 false *1 2.75,2.583 3.083,2.917 0.333,0.333 10 false *2 1.563,3.021 1.917,3.25 0.354,0.229 10 false *3 1.771,1.781 2.083,2 0.313,0.219 10 false *4 0.667,0.198 1.073,0.542 0.406,0.344 10 false *b 0.667,3.406 1.083,3.667 0.417,0.26 10 false *a 2.354,2.563 2.583,2.833 0.229,0.271 10 false A 1.979,2.563 2.167,2.833 0.188,0.271 10 false B 1.135,2.573 1.333,2.833 0.198,0.26 10 false C 0.771,2.573 0.917,2.833 0.146,0.26 10 false D 0.844,0.875 1.156,1.052 0.313,0.177 10 false H14 1.083,1.667 1.583,1.917 0.5,0.25 10 false MSW- 2.24,1.667 2.75,1.917 0.51,0.25 10 false MSW+ 1.833,4.271 2.417,4.5 0.583,0.229 10 false PMC+ 1.073,4.271 1.583,4.5 0.51,0.229 10 false PMC- 0.823,3.76 1.167,3.99 0.344,0.229 10 false H15
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H15-2 (PMC+) - H15-1 (PMC-) Always Below 1 Ω


Result:
Proceed to
OK
NG



c.

Disconnect the service wire from connector B.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR