Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P0560A2  System Voltage System Voltage Low  P0560A3  System Voltage System Voltage High  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal +B of the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P0560A2 System Voltage System Voltage Low Battery voltage is between 2.5 and 10 V when 180 seconds or more have elapsed since engine start (3 trip detection logic).
·

Open or short in backup power source circuit

·

Tired battery

·

Electrical over work

·

Generator

·

ECM


Comes on DTC stored Engine A
P0560A3 System Voltage System Voltage High Battery voltage is 17 V or more when vehicle speed is 25 km/h (16 mph) or more, after 180 seconds or more have elapsed since engine start (3 trip detection logic).
·

Generator

·

Battery (If 24 V battery is installed, DTC P0560A3 is output)

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A459178E01
0.406,1.906 1.51,2.146 1.104,0.24 10 false BATT-MAIN NO.1 0.552,3.031 1.198,3.219 0.646,0.188 10 false Battery 0.5,0.75 1.479,0.979 0.979,0.229 10 false EFI-MAIN NO.1 2.094,1.448 3.083,1.656 0.99,0.208 10 false EFI-MAIN NO.1 5.583,0.5 5.74,0.698 0.156,0.198 10 false 2 5.573,1.094 5.729,1.292 0.156,0.198 10 false 1 5.573,1.844 5.729,2.042 0.156,0.198 10 false 9 5.573,2.552 5.729,2.75 0.156,0.198 10 false 4 5.792,0.573 6.052,0.74 0.26,0.167 10 false +B 5.781,1.167 6.146,1.333 0.365,0.167 10 false +B1 5.792,1.896 6.24,2.094 0.448,0.198 10 false MREL 5.792,2.625 6.156,2.792 0.365,0.167 10 false E1 5.927,3.302 6.281,3.49 0.354,0.188 10 false A55 6.26,3.302 6.698,3.5 0.438,0.198 10 false ECM 1.979,0.521 2.135,0.719 0.156,0.198 10 false 3 2.844,0.521 3,0.719 0.156,0.198 10 false 5 1.969,1.042 2.125,1.24 0.156,0.198 10 false 2 2.854,1.042 3.01,1.24 0.156,0.198 10 false 1

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


·

DTC P0560A2 is detected when the engine idles for 180 seconds or more.

·

DTC P0560A3 is detected when the vehicle speed is 25 km/h (16 mph) or more and 180 seconds or more have elapsed since engine start.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OUTPUT DTC
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P0560A2 is output A
P0560A3 is output B




A

2.CHECK HARNESS AND CONNECTOR (ECM - EFI-MAIN NO. 1 RELAY)

B

3.CHECK CHARGING SYSTEM AND BATTERY
2.CHECK HARNESS AND CONNECTOR (ECM - EFI-MAIN NO. 1 RELAY)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-2 (+B) - 5 (EFI-MAIN NO. 1) Always Below 1 Ω
A55-1 (+B1) - 5 (EFI-MAIN NO. 1) Always Below 1 Ω
A55-2 (+B) or 5 (EFI-MAIN NO. 1) - Body ground Always 10 kΩ or higher
A55-1 (+B1) or 5 (EFI-MAIN NO. 1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK CHARGING SYSTEM AND BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CHARGING SYSTEM AND BATTERY

OK

NG

REPAIR OR REPLACE CHARGING SYSTEM AND BATTERY