Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the brake actuator assembly (skid control ECU) and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A213522E09
0.292,1.177 1.042,1.563 0.75,0.385 10 false from Speed Sensor 0.979,1.802 2.813,2.177 1.833,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 3,1.802 4.844,1.979 1.844,0.177 10 false Combination Meter Assembly 5.719,1.813 6.167,2 0.448,0.188 10 false ECM 2.625,0.542 3.156,0.708 0.531,0.167 10 false 4-Pulse 4.635,0.542 5.167,0.708 0.531,0.167 10 false 4-Pulse

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P050031 Vehicle Speed Sensor "A" No Signal While vehicle is driven, no vehicle speed signal to ECM (3 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Brake actuator assembly (Skid control ECU)

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A322493E01
5.635,0.781 6.094,0.979 0.458,0.198 10 false SPD 5.896,1.938 6.354,2.135 0.458,0.198 10 false A55 6.219,1.938 6.677,2.135 0.458,0.198 10 false ECM 4.969,2.385 6.958,2.583 1.99,0.198 10 false to Other ECUs 5.385,0.781 5.698,0.979 0.313,0.198 10 false 41 3.896,0.781 4.208,0.979 0.313,0.198 10 false 36 2.438,1.688 2.75,1.885 0.313,0.198 10 false H6 2.417,1.865 4.26,2.083 1.844,0.219 10 false Combination Meter Assembly 2.5,0.781 2.813,0.979 0.313,0.198 10 false SI 2.26,0.771 2.573,0.969 0.313,0.198 10 false 20 0.146,0.865 3.354,1.063 3.208,0.198 10 false from Skid Control ECU 3.646,0.771 3.958,0.969 0.313,0.198 10 false +S

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P050031 is detected when the vehicle is driven for 2 seconds or more at an engine speed of 1000 rpm or higher.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)

Pre-procedure1

a.

Drive the vehicle.


Procedure1

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 372 212

Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B


Post-procedure1

c.

None.



A

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - COMBINATION METER ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Disconnect the combination meter assembly connector.


c.

Disconnect the ECM connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-36 (+S) - A55-41 (SPD) Always Below 1 Ω
H6-36 (+S) or A55-41 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

e.

None.



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Start the engine.


b.

Drive the vehicle for 2 seconds or more at an engine speed of 1000 rpm or higher.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT


Post-procedure1

d.

None.



NEXT

END