Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminals of the ECM. When the transistor in the MREL circuit operates, current flows from the battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B1 terminals of the ECM.

WIRING DIAGRAM

A458582E01
0.406,0.292 0.719,0.49 0.313,0.198 10 false *1 3.656,0.292 3.969,0.49 0.313,0.198 10 false *1 0.448,1.583 0.76,1.781 0.313,0.198 10 false *2 3.667,1.583 3.979,1.781 0.313,0.198 10 false *2 1.51,0.188 1.781,0.375 0.271,0.188 10 false 6 2.844,0.198 3.115,0.385 0.271,0.188 10 false 24 1.719,0.354 2.031,0.552 0.313,0.198 10 false +B 2.417,0.354 2.823,0.531 0.406,0.177 10 false IGPD 1.542,0.719 3.063,1.125 1.521,0.406 10 false Certification ECU (Smart Key ECU Assembly)*1 0.719,1.854 1.125,2.031 0.406,0.177 10 false AM1 0.552,3.229 1.688,3.406 1.135,0.177 10 false BATT-MAIN NO.1 0.573,5.125 1.125,5.323 0.552,0.198 10 false Battery 1.51,1.583 1.781,1.771 0.271,0.188 10 false 7 1.708,1.583 2.115,1.76 0.406,0.177 10 false AM1 2.51,1.583 2.875,1.75 0.365,0.167 10 false IG1 2.823,1.583 3.094,1.771 0.271,0.188 10 false 8 1.25,1.969 1.604,2.156 0.354,0.188 10 false H54 1.25,2.135 3.844,2.365 2.594,0.229 10 false Ignition or Starter Switch Assembly*2 3.135,3.667 3.542,3.844 0.406,0.177 10 false IGP 4.573,3.219 4.979,3.396 0.406,0.177 10 false INJ 1.719,4.552 2.698,4.781 0.979,0.229 10 false EFI-MAIN NO.1 3.052,5.094 4.042,5.292 0.99,0.198 10 false EFI-MAIN NO.1 5.813,2.969 6.125,3.167 0.313,0.198 10 false 37 5.875,3.823 6.146,4.01 0.271,0.188 10 false 2 5.875,4.281 6.146,4.469 0.271,0.188 10 false 1 5.875,4.729 6.146,4.917 0.271,0.188 10 false 9 5.875,5.406 6.146,5.594 0.271,0.188 10 false 4 6.073,3.01 6.531,3.198 0.458,0.188 10 false IGSW 6.063,3.885 6.375,4.083 0.313,0.198 10 false +B 6.063,4.344 6.385,4.542 0.323,0.198 10 false +B1 6.073,4.729 6.531,4.917 0.458,0.188 10 false MREL 6.083,5.427 6.396,5.625 0.313,0.198 10 false E1 6.177,6.063 6.531,6.25 0.354,0.188 10 false A55 6.479,6.063 6.865,6.281 0.385,0.219 10 false ECM 1.979,6.135 4.833,6.344 2.854,0.208 10 false *1: w/ Entry and Start System 1.979,6.469 4.833,6.677 2.854,0.208 10 false *2: w/o Entry and Start System 2.833,0.385 3.292,0.583 0.458,0.198 10 false H45 1.365,0.385 1.823,0.583 0.458,0.198 10 false H46 0.677,0.531 1.135,0.729 0.458,0.198 10 false AM2 0.427,2.531 2.573,2.729 2.146,0.198 10 false INP STP NO.1-3 1.927,3.229 3.156,3.427 1.229,0.198 10 false IGP-MAIN 2.854,2.969 3.01,3.167 0.156,0.198 10 false 3 3.552,2.979 3.708,3.177 0.156,0.198 10 false 5 2.854,3.313 3.01,3.51 0.156,0.198 10 false 2 3.542,3.313 3.698,3.51 0.156,0.198 10 false 1 3.063,4.302 3.219,4.5 0.156,0.198 10 false 5 3.792,4.302 3.948,4.5 0.156,0.198 10 false 3 3.052,4.729 3.208,4.927 0.156,0.198 10 false 2 3.781,4.729 3.938,4.927 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspection the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-4 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A459385C02
0.073,0.042 0.385,0.198 0.313,0.156 10 false *1 1.573,2.156 1.885,2.313 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
2 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

4.INSPECT EFI-MAIN NO. 1 RELAY

OK

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay) - A55-9 (MREL) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A55-2 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A55-1 (+B1) Always Below 1 Ω
1 (EFI-MAIN NO. 1 relay) or A55-9 (MREL) - Body ground and other terminals Always 10 kΩ or higher
3 (EFI-MAIN NO. 1 relay), A55-2 (+B) or A55-1 (+B1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)
a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - A55-37 (IGSW) Always Below 1 Ω
5 (IGP relay) or A55-37 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT IGP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGP RELAY

OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)

NG

REPLACE IGP RELAY

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)
A459386C02
0.146,0.083 0.458,0.281 0.313,0.198 10 false *1 1.125,2.125 1.438,2.323 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 IGP Relay


a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGP relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)
a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)

B

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-24 (IGPD) - 1 (IGP relay) Always Below 1 Ω
H45-24 (IGPD) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

OK

12.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - IGP RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - IGP RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-8 (IG1) - 1 (IGP relay) Always Below 1 Ω
H54-8 (IG1) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR